a)If column dimensions are 250*400mm , what will be
cutting length for 8mm stirrups and how to calculate it? b)
If beam dimensions are 200*400mm , beam coveris 25mm , slab
cover is 20mm , what will be the cutting length for
stirrups? c)Column dimensions are 250*400mm , reinf. is
12nos. bar of 16mm dia , stirrups provided are two legged,
what will be the length of each ring?
Regards
- 27 Answers
- 189839 Views
- Alfaraa, Speco, Supertech, Welspun, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / er shailesh kr srivastava
A)CUTTING LENGTH FOR 8mm Strips=2(250+400-2*80-2*8+24*8)
2(650-160+22*8)
2(490+176)
=1332mm
same as for beam
| Is This Answer Correct ? | 6 Yes | 9 No |
Answer / ajay
sir , my name ajay kumar ,working on site i also had the
same problem of estimation , but sir ur answer was so nicely
explained , im very thank full to u for ur valuable and
precious information, sir can i no ur email id and no so i
can get some knowlege from u ?
my email -ajaykapse2@gmail.com
| Is This Answer Correct ? | 6 Yes | 10 No |
Answer / ram bhawan
2(A+B)+16*DIA OF STIRRUP BAR
A = INNER HEIGHT OF STIRRUP
B = INNER BREATH OF STIRRUPS
IF CLEAR COVER IS GIVEN (COVER GIVEN FROM STIRRUP NOT FROM
MAIN BAR)
| Is This Answer Correct ? | 2 Yes | 9 No |
Answer / silpa
250-25+8=233mm,
400-25+8=383mm
2(0.233+0383)+16*0.08=2.512m
| Is This Answer Correct ? | 9 Yes | 32 No |
Answer / anthony victor bernard
a)250-column cover both side+8*dia of rod
400-column cover both side+8*dia of rod
so cutting length is (.200+.350)*2+(2*5*.008)
=1.180 mts
(b)cutting length is (.150+.355)*2+(2*5*.008)
=1.090 mts
(c)cutting length is (.100+.350)*2+(2*5*.008)
=0.980 mts
| Is This Answer Correct ? | 11 Yes | 38 No |
a)250-column cover both side+8*dia of rod
400-column cover both side+8*dia of rod
so cutting length is (.250+.400)*2-.160+.128
=1.268 mts
same as (b)
| Is This Answer Correct ? | 37 Yes | 65 No |
what is the factor of safety for cement and steel with reference to IS 456-2000. and min reinforcement should be provided for column and slab with reference to IS 456-2000.
the amount of gypsum usuallyin the manufacture of cement
what will be the quantity of following materials in P.C.C for the total area of (100'x70'x 0'4") 1)NO. OF CEMENT BAGS 2)SAND IN CU.FT 3)METTLE IN CU.FT
0 Answers Pratibha Industries,
How much concrete can be made using one bag of cement?
is there any codal provision for soil cousion over the Hume pipe of Dia 1.2 m.
How steel required for 823 sqm of flooring work in 150mm c/c in single jali?
In olden days reinforcing bars in concrete are not got rusted even till now. But recently provided steel getting rusted in concrete. what are the probable reasons?
Explain major differences between routing maintenance and major maintenance.
Write down a formula to calculate the number of 50Kg bags of cement for moulding of cement blocks of tcm thick by 20cm high by 40cm long on site with a mix ratio of 1 bag of cement to 3 wheelbarrows of sand . the sand is measured at a STRUCK( WATER LEVEL) 65 litres capacity wheelbarrow. TEL: +237 674630019
how many quantity of water use in 1cu.m. concrete
how is the wastage component in structural steel being considered while doing the reconcillation for the fabrication with returning of scrap under 1 meter length
4 Answers LIC, NTPC, Tata Steel Limited,
what is mixed design, define it? what is way beecher?
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
