Answer / rvg

Two eathing are req. minimum. Since the star point is
earthing solidly, and obviously the generator frame/housing
also to be provided with earthing to prevent any shock due
to insulation failiure.

if the generator is connected with a fuel tank, (for higher
size), it is necessary that, fuel tank to be grounted to
prevent lightning surges and any static voltage generations.

Answer / saleem

2nos for body and 2 nos for neutral earthing.Is there any
corrections ?

Answer / sudheer siddani

depends on the rating of the generator upto 125kVA two
earthings is sufficient one is neutral and one for
body.>125kVA four erthins are required two for neutral and
two for body

Answer / rajeshsan

The earthing of Generator at star point is depends on the capacity.

For larger generators eg:- 600MW generator the generator is grounded using NGT and generator body is grounded at two ends. Earthing are done at two ends to have redundancy only.

Answer / pankaj singh

there should be two earthing required.one for star point
and another for body. At the star point there should be a
solid grounding,on the other hand body frame should be
earth diagonally and the material for grounding depend on
the rated valtage of generator

Answer / ajay kumar das

Normally minimum 4 earthing required .2 for body earth & 2 for neutral,But in case for 11 KV generation another 2 earth is required for L.A.

Answer / bhasker reddy

Depends on the KVA rating of generator earthing are required.
less than 40 kva atlest 2 earthing(one neutral & one body earth). more than 40 KVA 4 earthing (2 neutral & 2 body earth). if KVA rating increased should increase earthing.

Answer / gunasekaran

their are two system earthing at single voltage level in
generation one is generator neutral another one is PT
earthing and body earthing also provided

Answer / nagaraj u.n

2.( body or frame) earthing should be used.because in case
of 1st point is faild ,2nd point is worked .it safety for
generator & opperatore.

Answer / kiran patil

Only one at the star point of generator which should be
solidly grounded

what is the maximum permissible limit value of leakage current and leakage counter reading to replace lightining arrester?

0 Answers  

how a resistor resists to flow the current?how an inductor oppses the sudden change in current?how a capacitor opposes a DC voltage.

0 Answers   Hindustan Unilever Limited,

Why the motor take high starting current for long time(10- 15 sec) which is connected to Blower as compaire with a motor which is connected with pump with same rating?

2 Answers  

Our transformer capacity is 500kva & voltage ratio is 11kv/433v step down tf.Now i need to know if my input voltage is 10500v and what would be the secondary side voltage i.e output voltage ?

3 Answers   Helma,

What is difference between insulating medium and fault current interruption medium in a switching device.

0 Answers  

WHAT IS THE MEANING OF CYWY

1 Answers  

A 3 phase transformer's (Y-Y) Y and B phase is (Y and B connection not broken) broken from neutral and R and Nutral connection is ok, what will be the relay tripping and why

0 Answers  

How to Calculate The Neutral Earth flat design calculation for the Synchronised generator (Gen 1-650Kva, Gen 2-725Kva

0 Answers  

Two alternators say 1 & 2 are poised to parallel operation. But at the time of paralleing alternator 2 gets out of the system by tripping Earth fault relay. Please send me reply why this is happening?

2 Answers  

If the rated speed of a d.c. Shunt motor is1440 r.p.m, which method of speed control would you suggested to obtain a speed of 1500 r.p.m?

0 Answers  

how i calculate the syncrones generator NGR resistance .if we have a 6mw generator line voltage of generator 11kv also line current 393.3 ampere.

0 Answers  

In a 3 phase induction motor(without connecting supply) if we rotate its rotor by hand and check resistance of stator winding at motor terminal box its resistance varies why ??

3 Answers   Jindal,