Answer / vinothbhabu

hello dear,jointing the cable not by using transformer or
by fevicol,and its not a simple like paper r wood jointing
by fevicol..
by using the heat strinkable method cable jointing will be
done,the heat strinking method gives high insulation to the
cable at jointing end,it can be used for jointing ht panel
board at the termination end,the kit used for the heat
strinkable is heavely insulation material,the joint will be
done by heating material...
for jointing the LT to LT cable above 6
sqmm,10,16,35,50,70,90,120,150,185,240,300,400,sqmm cable
by jointing the FERRULE LUG between the cable joint by
using cripping tools and then insulation tape will be
rounded it heavely......

Answer / rvg.msceb

heat shrink joint is the best method. please check with
Rechem website.

No there is a new tehnology update that is Cold shrink
joint.

Answer / jyotirmaya patra

The question is itself creating confusion. Are you asking
about the connection/jointing method,
or are you askinmg about the connection between HT-LT voltage?

Answer / sanjeet swarnakar

HT line tuns into LT by step down txr then connected lt
with LT cable

Answer / pravesh

h.t. cables are joint by using h.v. straight througk joint
if it is cable and then heat shrink by using the
insulation .
l.t. cables are joint by using l.v. lugs and covered with
insulation and heat shrink or may be taken to H pole
structure to join with thimbles.

Answer / rajendra

to joint these cableslike L.T. & H.T. cables there are many
componyes are providing the jointing kit for low tansion
cable in that kit some insulating material,lugs,earthing
wire, past to fill in joint are avable and instrction
manual also avable with kit. so we must read the jointing
procidure in the instruction manual & use this material to
joint the cable.

Answer / mehul g. c.

you should not join h.t. & l.t. cables because both are used
for the different current rating & voltage rating.

if you are asking about connection then
1. for step up & step down the voltage you can connect to
the transformer.

2. for distribution you can connect to breaker.

or

if you are asking about jointing then it is not good but

1. you can joint by jointing kit. ( heat srinkeble ) as you
asked your cable is h.t & l.t it 3-core & more than 25
SQ.MM SO There is no other way to joint it.

Answer / dilip b shah

H.T cable joint can be done by two method.
By Heat shrink kit or by m seal kit.If cable is unearth
prefere to use heat shrink kit. in earth cable prefere to
use m seal kit.
Two L.T Cable joint done by m seal kit(low voltage kit)
and end termination done by bimatalic lugs.

Answer / mukesh kaushik

HT to LT can't be joined directly. So, interface used for
interconnection is Transformer.

Answer / praveen

hi friends
ht and lt joints are not so easy
it need concentration and special care
first we should remove the area which was damaged
remove the sleeve and insulated material(ht cable)
use feruls and then crimp them with crimping tool
then use mastic tape to cover the feruls
next place the heat sink sleeves and heat them with
electric hot blower(hot air gun)

if we increase frequency of line, then how will string efficiency varies with it.

2 Answers  

what is the string efficiency

1 Answers  

can transformer of different kvas be paralled

2 Answers  

30 kva ups may kitne output voltage hote h

1 Answers   ME,

11kv alternator commissioning test?

2 Answers  

what is meant by frequency ?

10 Answers   TCS,

hi pot test principal

1 Answers   NTPC,

Why only three phase power generation are load are used

2 Answers   BARC,

wht is embedded systems? what is new inthis field?

0 Answers  

hello if any one have papers vof hpcl or sail, plz send me

0 Answers  

how to flameproof electrical motor on the shaft?

0 Answers  

role of europe union in UK safety legistlation (electrical safety)

0 Answers