What is the thumb rule for calculating the number of chairs in slab?

Answers were Sorted based on User's Feedback



What is the thumb rule for calculating the number of chairs in slab?..

Answer / sandeep thakur

01 chair per sq.m

Is This Answer Correct ?    66 Yes 9 No

What is the thumb rule for calculating the number of chairs in slab?..

Answer / er.prabhakara.b

As per IS:2502-1963 Clause 7.4.2
SL&s - In slabs, whether double or multiple, layers of
reinforcement are provided, the distances between the
layers may be maintained by the method illustrated in Fig.9
The Code does not Specify the Exact Spacing of the Chairs
but in Practal the Spacers are provided based on the
Spacing and Dia of Main Reinforcement it is 1 Chair per Sqm

Is This Answer Correct ?    34 Yes 9 No

What is the thumb rule for calculating the number of chairs in slab?..

Answer / 9040471784

1. Chairs are provided for maintain the proper gap between the 1st layer & 2nd layer.
2. In IS Code it is not mentioned the chair spacing.
3. As per my experience it should be provided 1 chair in 1 sqm.
4. If the slab is 6 sqm then there will we use 6 nos of chairs

Is This Answer Correct ?    9 Yes 4 No

What is the thumb rule for calculating the number of chairs in slab?..

Answer / moamen saad

calculate the buckling affecting the chair branches due to dead and live loads comes from top mesh load and wight of labors, check it with allowable buckling.
i did an excel sheet according to ACI-318

Is This Answer Correct ?    1 Yes 0 No

Post New Answer

More Civil Engineering Interview Questions

Define What is a projection line?

0 Answers  


what is the slump of pile concreting work? give me the value of minimum and maximum value of slump and how give slump in pile?

3 Answers  


one cubic meter of concrete contains how much proportions of cement,sand and course aggregate

6 Answers   AB Inc, APPSC, Arif Builders, Ramky, SMEC,


What Are The Different Type Of Slump Test Indications?

0 Answers   Bechtel,


What are the techniques to measure road difference?

0 Answers  






Explain creep?

0 Answers  


corrosion of reinforcement bars due to chloride attack and its equation

2 Answers   TATA,


how will remove spiderweb cracking in plaster ? what the reasone of make it ?

0 Answers   Bharat, JLV,


what is anchorage length,lap length and (dont remember the last one)

0 Answers   Bhansali Group,


all rod lapping formula

3 Answers  


How much overlapping required for welding the reinforcement bars in Columns & beams

3 Answers  


GIVE US YOUR FULL DETAIL OF THE FOLLOWING… FULL NAME.. PERMENENT MAILING ADDRESS DIRECT CONTACT NO E MAIL ADDRES.

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)