Answer / simpal

DC motor starter is called 3 point starter bcoz only 3
terminal (L,A,F)are available from starter.These 3 terminal
L(line),A(armature),F(field) must b connected to supply
terminal,motar armatuer terminal,and shunt field terminal.

Answer / c.balakrishna moorthy

Actually Dc motor starter are classified as two point
starter,three point starter and four point starter.
Three point starter is used in case of Shunt motor(some
cases this can be used compound motor also)
Four point starter is mainly used in compound motor.
Two point starter is used in series motor in order to make
the motor to run in safe manner.
Three points denotes Line terminal.field terminal and
armature terminal in which three points are connected.
three points L,A F.
that is the main reason

Answer / ravi693

Beacuse this 3 point starter has three points to save the
motor.
1) over load protection
2) no volt protection
3) starting huge currect protection

Answer / nagaraju .n

In an dc motor have 1.armature
2.field
3.supply
in an 3point starter have 3point(L A F ),
it limits starting armeture current.because armeture is
very low resistence.


that way adding resistace series with the armature 3 point
starter should be used.

Answer / siddarth.m

the main purpose of using a three point starter is
to limit the starting armature current.......
This is because dc motor the initial voltage difference is
less so high current passes through the armature windings
which is not a desired factor.When we use a 3 point starter
it slowly induces the back emf in motor so that the voltage
difference is less and rate of current flow is less, so the
motor doesnt get spoiled

Answer / saila sandeep

because it has three terminals i.e;'l' 'f' 'a'
'l' is connected to supply
'f' is connected to feild circuit
'a' is connected to armature

Answer / srithar

a three point starter is onely usst four three point
(l,f,a) line,field,armature. so itis called as three point
starter

Answer / karthick

because it has three terminals line,field,armature.these
three terminals are connected to their respective ones in a
motor.

Answer / rajeshwar kumar

dc motor starter is called 3 point starter it has three
terminal (L A F)(LINE,ARMATURE,FIELD) IT USED INSHUNT
MOTOR

Answer / sundar

Because they have three terminals namely line field and
armature. they are connected with the motor respectively,

Expand sqcm?

2 Answers   UltraTech,

how to calculate the distance relay faulty zone?pls explain?

0 Answers  

what is the question paper model for section engineer in RRB

0 Answers   RRB,

I am a possesor of c licence from 1993. I forgot to renew during the year 1998. During that time I was working at TNEB to till date. Is there any possibility to get renewed? or to apply for a new one?

0 Answers  

fuses rated by amperes but not power,why?

3 Answers   Blue Star,

How can I calculate the Mega watts required to run a plant having many electric motors and other electrical components.

0 Answers   ISS,

what is transformer?

4 Answers   Mphasis,

Why short circuit calculation is not required in LT cable sizing and requiredin HT cable sizing only

2 Answers   Chemtex,

working principle of current sensing relay? how its work?

1 Answers  

I don't understand why when we connect high voltage source in DC to electronic motor , we must add capacitor and resistor in parallel ? (I know that we use capacitor because we want to absorb the current that in the first second electronic motor in opposed with current course produce. ) what are the feature of Resistor and in such situation ?

0 Answers  

if a motor is running at 1500rpm then how you can find its HP

1 Answers   Construction,

WHY IS THE EARTH FAULT CURRENT ALWAYS LESS THAN THE NORMAL CURRENT??

0 Answers   Teil,