Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


In a parallel circuit dc circuit with two resistors, if you
know the voltage, amperage, and one resistors ohms, what
formula is used to find the second resistors ohms?

Answers were Sorted based on User's Feedback



In a parallel circuit dc circuit with two resistors, if you know the voltage, amperage, and one re..

Answer / shobana

Current Division Technique.

We know that Voltage in parrall will be same. Only current
will divide. As we know V, I(total), R1 we can use the
following formula:
I1 = (R2/R1+R2)* I(Total)
I2 = (R1/R1+R2)* I(Total)

Is This Answer Correct ?    5 Yes 0 No

In a parallel circuit dc circuit with two resistors, if you know the voltage, amperage, and one re..

Answer / woot

The equivalent resistance of the circuit is V/I. Then use
this equation: Req = (R1*R2)/(R1+R2).

Is This Answer Correct ?    6 Yes 1 No

In a parallel circuit dc circuit with two resistors, if you know the voltage, amperage, and one re..

Answer / shane e.

VT/IT=RT
RT-R1=R2

Is This Answer Correct ?    0 Yes 0 No

In a parallel circuit dc circuit with two resistors, if you know the voltage, amperage, and one re..

Answer / shane e.

I1=Vt/R1
I2=It-I1
R2=Vt/I2

Is This Answer Correct ?    0 Yes 0 No

In a parallel circuit dc circuit with two resistors, if you know the voltage, amperage, and one re..

Answer / harshavardhan

See in parallel circuit wecan apply voltage,current divider
theorem where tats it u will get it

Is This Answer Correct ?    2 Yes 3 No

In a parallel circuit dc circuit with two resistors, if you know the voltage, amperage, and one re..

Answer / pillay

use only ohms law.

Is This Answer Correct ?    0 Yes 1 No

Post New Answer



More Electrical Engineering Interview Questions

In what circumstanced the CT used for protection relay will be saturated?and what will happen to the relay is the CT is saturated?

3 Answers  


When calculation of fault current and fault Kva is to be done,why always we use per unit value and why we consider the base kva?

0 Answers  


Why the earth cable have current 1A - 2A , it is safety for Electrical system or earth cable should be zero amps ? how to troubleshoot?

0 Answers  


Transformer diagram mention each parts ?

0 Answers  


Which type of control system is expensive — closed loop or open loop?

1 Answers   GE,






What do you mean by reverse current braking of an induction motor?

1 Answers  


what happens to current , when voltage drops .?

11 Answers  


whytransformers rating in KVA?

3 Answers   Chettinad,


how many BUSBAR is in electrical system?

3 Answers  


What is the BS(British Standard)code for 11kv motor

1 Answers  


In one village i have seen Earthing transformer's earthing line was also connected to the Transformer body to ground the transformer,can it be possible to maintain 0Volt reutral line this way?

2 Answers  


Hi frnds :) plz tell me that i have 100 KVA 3 phase generator so by thumb rule 100*1.4 = 144 amps and generaly we can operate at 80% load...so it will 144*0.8 =112 amps.... so now i m confused about single phase load.....if we use that generator only for single phase the that 112 amps is total single phase load or i can give 112 amps at red 112 amps at yellow and 112 amps at blue.... i mean that total single phase load that 100 KVA generator will take is 112+112+112=336 amp ??

2 Answers   FWO,






Categories
  • Civil Engineering Interview Questions Civil Engineering (5074)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4445)
  • Electrical Engineering Interview Questions Electrical Engineering (16595)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2986)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (122)
  • Power Plant Engineering Interview Questions Power Plant Engineering (170)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1377)