Answer / thunderbolt

More power is transmitted .

Answer / vilas

As used 3 phase balanced supply ,we get the advantage to
reduce the size of the motor, no need of capacitor ,
getting improved power factor ,constant torque,saving in
copper for winding ,thus redues the costof the motor,

Answer / balaji

1.if we use all loads in a single phase voltage drop will be
high.instead of that if we use 3 phase then load will be
shared by each phases ,so voltage drop will be less.
2.we can use 3phase load as well as 1 phase load in 3phase
4wire system.

Answer / sunil guru

IN 3-PH COMPARED TO SINGLE PHASE LOSSES ARE LESS..
LARGE POWER IS TRANSMITTED SO THAT A GREATER NEED CAN BE
FULFILLED..
WE CAN TRANSMIT POWER TO A LARGE DISTANCE WITH LESS COST OF
TRANSMISSION AS COMPARED TO SINGLE PHASE.
IN INDUSTRIAL SECTORS THE MACHINERIES AND EQUIPMENTS ARE OF 3-
ph SO 1-PH CANT BE MADE INTO USE...

FOR ANY DISAGREEMENT MAIL ME AT parmar20072008@yahoo.com

Answer / adisurendra bandi

using of 3 phase instead of 1 phase,we must get advantages in terms of Economic aspect as well as we get very efficient performance than the single phase,because of we are sharing the load on from single phase to 3 phase.

Answer / sivasellam

losses will be reduced.less cost.for long distance it is
used to transmit

Answer / sunil parmar

if we can use 3 phase system losses will be reduced,cost will be reduced,load sharing will be equally,so voltage drop less and power quoality should be maintain in distribution and x' mission.

Answer / arun

single phase cannot handle heavy loads but 3 phase can handle heavy load .eg single lane highway produce traffic signal but 3 lane highway not produce traffic signal .but in practical when domestic loads consume more than 745 hp 9horse power power so we have to use 3 phase load

Answer / abhishek roy

In industries there are large machines are used which is only depend on 3-ø supply.

Answer / any

with 3 phase we can transmit constant power as in case of
single phase power varies sinusoidally,
greater output,
chaper,economy in power transmission

Can we inject more current in ct primary paralleling 2 loading transformers/Injection kit at a time?let ct ratio be (5000/1A)(per kit rating 2000A range),i need to inject 5000A,if this cant b done means wat is d optional?

1 Answers  

what is the relationship between current&voltage in practical purpose ?

1 Answers   Indorama,

What is spike & surge.

2 Answers  

What is the formula for calculating the Instantaneous Short Circuit & overcurrent for any breaker

0 Answers  

What are thermo couple cables and where they are used.

2 Answers  

I want to know which cable would be best to carry 125A current to a distance of 50m. Voltage is 3phase. Kindly share the formula with answer.

1 Answers   Medway Educational Consultant,

what happen if i connect DYn11 and DYn1 vector group transformer in parrallel?other things are same like votage ration,x/r ratiob etc...

4 Answers  

why we use primary delta connectin in hight voltage transformer

2 Answers  

Differentiate between power relay and reverse power relay?

2 Answers   ABB, TVS,

i seen a 132kv/11kv transformer,and thier is a sugar factorys 10MW EXPORT PLANT,MY QUESTION IS THAT WHEN THEY EXPORT ELECTRICITY THEY USE THE SAME TRANSFORMER AND THE CONNECT IT TO 132/11KV TRANSFORMERS SECONDARY SIDE CAN ANY ONE EXPLAIN IT.. THE TRANSFORMER IS OF KIRLOSKAR MAKE AND IT HAS TAP CHANGER.

1 Answers  

HOW TO MEASSURED THE AMPS RATING FOR SUITABLE CABLE SIZE?

4 Answers  

What is the high tension lines voltage and low tension lines voltage?33 kv is high tension line or low tension.

1 Answers   MPSEB,