Answer / tareq harb

synchronizing is making phase, voltage & frequency the same
or with small difference between generators.

paralleling is sharing the load among all this generators.

so synchronizing is done before closing the ckt breaker but
after closing it parlleling process starts and all above
mentioned parametrs stuck together.

Answer / iamdon

Synchronization (in the context of electrical engineering)
is the process of attaining exact co-ordination(Relative
should be zero) between two or more, similar time varying
quantitites.The quantities involved must has same rate of
change.Synchronization is a global concept(exists through
out the system).

Paralleling is the process of placing more than one systems
aganist same condition to achieve common goal.In some cases
(parallel operation of alternators,parallel operation of
transformers etc.)synchronizion is must for paralleling
where as in some cases(Paralleling loads across a supply
etc.) in is not must for loads to be synchronized.
Paralleling is a local concept(Prevaling at few places and
these places are independent with each other)

Author:arbelectbit@yahoo.com

Answer / prabhakar

synchronization is done between two similar equipments
(generator,transformer) w.r.t FREQUENCY,KVA RATING MUST BE
SAME.

Answer / shaibal saha

Any two or more systems that has parameter(such as
frequence,phase etc.) transfer function of time dependance,
when coupled to achieve output or input simultaneously
called synchronisation contrary to same phenomena when
parameters have no time dependance called paralleling.

Answer / bala sundaram

parallel

any two or more alternator connected to grid and share a common load its called a parallel operation.

synchronizing

how to connect to grid (depend a voltage,frequency,phase sequence)a alternator is called a synchronizing operation.

Answer / safeer ahmad

When two or more machine having same voltage,current and
frequency on working condition its called synchronism

and when we want to share the load two ore more machines in
parallel its called paralleling..............

Answer / pavan kumar

parlleling and sychronization are very similar that when two
generators are in sychronization or running simultaneously
is called parlalling and sychronization means keep the
parameters like voltage, frequency and phase sequence of the
two machines
equal with respect to each other. that means the voltage,
frequency, phase sequence waves of the first generator
should be equal to the voltage, frequency and phase sequence
of the second generator

Answer / ramireddy

Synchronization is the process of connecting alternator to
the grid system or aiternators which are already connected
parllely.
after it is syncronised to the grid system then it is said
to be working parrlel with another alternators

Answer / anand

Running of two similar systems by keeping voltage,phase
sequence and frequency same is known as paralleling (ex:
two or more D.G sets or two or more transformers).

Running of two dissimilar systems keeping the above
parameters same is known as synchronization (ex:D.G set and
transformer).

Answer / sangram patil

Parallel:- in this process you dont have concentrate on
equality of Voltage, freq & phase angle. its a simple
method of devidation, so its easly to devide load on one or
more m/cs.
Synchronisation:- in this process you have must be
conentrate on above parameters because its become direct
affect on source. it can be happen one or more equipments.
which should be done before loading the m/cs.

WHICH SUPPLY IS BETTER FOR 4 MW LOAD. 1)TO TAKE NEARER AVAILABLE 11 KV SUPPLY OR 2)TO TAKE 33 KV SUPPLY WHICH IS AVAILABLE AT 10 KM DISTANCE BY INVESTING NEARLY 50-60 LACKHS

1 Answers  

How to model two generators into a single generator ? Eg. two generators connected to a bus, would like to model it as a single generator connected to a bus.

0 Answers  

If you see the HRC fuse name plate. Its shown ampere rating shown which is in many KA (like 80KA and so on). any body explain what is meaning of this value?

7 Answers  

Why converter duty transformer neutrals are not earthed...i am still not sure if this question is also correct...Please email at ranjan120482@gmail.com

0 Answers  

a.c&d.c motor&generator

2 Answers   Vizag Steel,

why tan delta test is carried out in the power transformer? which parameter are measure?

1 Answers  

condition Autotrip facia come on control panel of electrical transmission line?

0 Answers   Getco,

what is the diffrence between resistive load and capoasitive load.?

4 Answers  

why can we use cosine wave instead of sine in ac supply as both have same rms vale and ripple factor

0 Answers   Indcoil Transformers, Power Grid,

what is multiplying factor of a energy meter connected with a CT ratio of 600/5 and voltage at 415 volts.

1 Answers  

Dear all, how we select the cable size according  to current with or without including different correction factor , is there any direct method for sizing of cable... 

0 Answers   Kharafi National,

what is the difference between earthing and grounding?

6 Answers   Bhel, Wipro,