Answer / gopalkrishnan

Dead weight tester used for pressure gauge, pressure
transmitter, pressure switch calibration in high range.
(Kg\cm2or bar). it is used for industrial purpose in
instrumentation department.

Answer / praveen kumar

Dead Weight Tester is Master calibration equipment for
calibration of Low & High pressure ranges, Instruments i.e
Transmitters,Switches, Gauges also.

Answer / guest

Dead weight tester is used for calibrating prssure gauges.

Answer / vinod

Deadweight Tester (Pressure Balances)
are the most accurate instruments for the
calibration of electronic or mechanical
pressure measuring instruments. The direct
measurement of pressure, according to its
definition as a quotient of force and area,
and the use of high-quality materials result
in small uncertainties of measurement and
an excellent long-term stability of five years.
For these reasons, deadweight testers
have already been used in calibration
laboratories of industry, national institutes
and research labs for many years.

Answer / x y z

Dead weight tester is the test instruments, in which the
required test instruments is checked aganinst the standard
weight. And it is used to cablibrate pressure gaure and
PRV.

Answer / vinesh prajapati ,guj. +919974

Dead Weight Tester is Master calibration equipment for
calibration of Low & High pressure ranges, Instruments i.e
Transmitters,Switches, Gauges.

Pressure=Dead Weight/Area of piston

Answer / amith

Dead Weight Tester Is A Instrument Used to Caliberate the
Pressure Guage,Pressure Transmitters, Pressure Switchs,It
Is A industry Based Applicaion Instument.

Answer / prasad

dead weight tester is preasure calibration equipment used
ininstrumentation calibration labs basically meant for
calibrating preasure gauges,transmitters, preasure switches
etc.it is a primary standard for preasure calibrations

Answer / xxx

Dead wt tester is a caliberation gauge wherein you balance d
pressure due to known wt wit tat of ur unknwn pr gauge...

Answer / khustar9769797739

Dead weight tester used for pressure gauge, pressure
transmitter, pressure switch calibration in high range.
(Kgcm2or bar). it is used for industrial purpose in
instrumentation department

plz send me placement paper of ongc

0 Answers   ONGC,

I have 0.75mm sq multicore cable (IS type) , can use instead of same type but 1.5 sq mm cable ? Note : The distance is around about 150 meter.

1 Answers  

Can please tell mi about SIOS, PRM, SERVER, and what is the diference between PIN LAN, PCS LAN,APC Server, and please send the Doc if possible for referance,mail id patil_amit17@yahoo.com

1 Answers  

How to consider the flow directions for control valve (Globe) Is the there any easy understanding in order to select the flow directions?

3 Answers  

what is the procedure for auto tune in masoneialn 12300 series displacer type transmitter?

1 Answers  

sir i m preparing for BARC but i am not getting any papers to prepare for this exam so please send me some sample papers to my i.d for the preparation of barc.

0 Answers  

why we go for pcbs

2 Answers  

Is it ok, to use non-contact type Radar type LT, on a tank that is half circular from the bottom side? If yes the, isn't the waves gonna bent in other directions? 

1 Answers   Process Control Technologies,

If a differential pressure transmitter is calibrated for 0~2500 mmH2o and transmits a 4~20mA dc signal. The transmitter is placed across an orifice plate which is sized to create 2500 mmH2o differential at 5000m3/Hr a) what is the flow rate when the transmitter signal is 13.0mA DC? b) what is the signal output of the transmitter when flow rate is 2500 m3/Hr ?

5 Answers  

what is buoyancy law?

1 Answers  

HOW DOES SPECIFIC GRAVITY AFFECT LEVEL MEASUREMENT.

3 Answers  

what is zero trim and span trim?. at which problem we need to use this?

3 Answers