parallel operation for tansformer which condition fill fil
for that
Answers were Sorted based on User's Feedback
Answer / siddikh
1.polarity must be same
2.phase sequence must be same
3.turns transformation ratio must be sane
4.frequency must be same
5.% Impedence must be same
6.Vector group should be identical
| Is This Answer Correct ? | 19 Yes | 1 No |
Answer / irfan
1.polarity must be same
2.phase sequence must be same
3.equal voltage
| Is This Answer Correct ? | 11 Yes | 6 No |
1.polarity must be same ( Must be full fill )
2.phase sequence must be same (Must be full fill )
3.turns transformation ratio must be sane ( Desired )
4.frequency must be same ( Must be full Fill )
5.% Impedence must be same ( Desired as to ensure equall
load sharing of both the transformer
6.Vector group should be identical ( Desired )
| Is This Answer Correct ? | 6 Yes | 1 No |
following
1- KVA rating should be same
2- Voltage should be same and
3- frequency should be same
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / manoj tyagi
1. same voltage ratio
2. the per unit leakage impedence of the xer r based on
their own kva rating must be equal
3. ratio of eqv. leakage reactance to eqv. resitance should
be same for all the xers
4.transformer must be connected properly
| Is This Answer Correct ? | 2 Yes | 3 No |
Answer / ashok
1)polarity will be same.
2)phase sequence must be same.
3) turns ratio will be same.
4)impedance will be same.
| Is This Answer Correct ? | 0 Yes | 1 No |
Answer / vilas
1)Transformer primery voltage rating should be same.
2)phase sequence should be same .
3)polarity should be same.
4) Vector group should be same ,for example :dy11 etc.
These point to be considered while making parallel
operation of the tansformer.
| Is This Answer Correct ? | 0 Yes | 2 No |
Answer / maneswar
1.polarity must be same
2.phase sequence must be same
3.turns transformation ratio must be sane
4.frequency must be same
| Is This Answer Correct ? | 3 Yes | 6 No |
Answer / khalander mulla
to manage load at integrated steel plant to recover plant
load
| Is This Answer Correct ? | 0 Yes | 4 No |
How Arc Produced in Circuit Breaker When the contacts of the circuit breaker open.
1.Why sinle phase motor is not self starting 2.working principle of alternator 4.list out electrical formula
what is the MNA in case of d.c. machin? whaty is the importance of it? hoe it affect the brush position?
A 12.5 hp slip ring motor taking high initial current and its MPCB is getting open.what may be the reason?
which motor is used in watch..??????
. The string effcy in AC sys is 80% Then for same power, the string effcy in dc sys is a) less than 80% b) 80% c) more than 80% d) zero
1 Answers Engineers India Limited,
What is breather? why we use it ?
how we calculate electricity unit ( meter unit.. for knowing how many charges) from on motor load.?
How big (size) can the tertiary winding be in transformer? Can we load the tertiary winding, if yes then how much we can load it?
What effect does a very low impedance have on the Voltage regulation? On the short-circuit current?
What if high voltage side circuit breaker of a ehv transformer instead of lvcb? Kindly elaborate.
0 Answers MSETCL Maharashtra State Electricity Transmission Co Ltd,
What do you mean by ACB and VCB?
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)