How the CT and PT ratings are calculated

Answers were Sorted based on User's Feedback



How the CT and PT ratings are calculated..

Answer / ravi

depending up on the number of windings in primary and in
secondary winding,we can calculate the CT and PT rating of
the transformer.
N2/N1=V2/V1

Is This Answer Correct ?    13 Yes 9 No

How the CT and PT ratings are calculated..

Answer / m u shetty

First we should know whether CT /PT is used for measurement
purpose or for protection ,primary currentand voltage
After getting the above details ,we can decide the
specification of CT/PT like accuracy
class,ratio,burden,type etc

Is This Answer Correct ?    5 Yes 1 No

How the CT and PT ratings are calculated..

Answer / nagarajan

OK BUT WE WANT MORE DETAILS WITH FORMULA ALSO

Is This Answer Correct ?    1 Yes 1 No

How the CT and PT ratings are calculated..

Answer / hanu1985

OK BUT CAN GIVE SOME MORE DETAILS FOR ME

Is This Answer Correct ?    1 Yes 2 No

How the CT and PT ratings are calculated..

Answer / chandrasen mourya

Its Basically the requirement of the client.
ie. The client operationg load along with consideration for
future loads. This gives you the power, now for the Volatge
& current we have to do a bit survey regarding which
voltage level is available in the vicinity & the availibity
of the same from the electricity board. This gives us the
Volatge rating & current is now calculated.
Now we have to see what protection are required & depending
on that we select the no of cores in both The CTS & PTS.

Is This Answer Correct ?    5 Yes 11 No

Post New Answer

More Electrical Engineering Interview Questions

when transformer in load condition neutral earth testing wheater we can do it or not

1 Answers  


What would cause a 240v choke that should give 110v out on a 16w lamp to gradually increase to 160v?

0 Answers  


why the vfd motor take current high in vfd panel then mcc panel.current in vfd panel=160A in 93%.and mcc panel it shows 130A. (132kw motor)

1 Answers  


how could we findout the lightning arrester failed or not in live circuit? Is there any instrument to measure the high voltage at the time of sky lighting?

1 Answers  


In HVDC LINE RECTIFIER CONTROL ON CONSTANT CURRENT AND INVERTER CONTROL CONSTANT EXITATION ANGLE CONTROL BUT HOW INVERTER CONTROL CONSTANT CURRENT?

0 Answers  






When charging a 20 MVA , 33kV/6.6kV transformer through regulated (0-6.6 kV or 0-33 kV) source on no load , what will be the maximum current drawn by transformer from source and what sould be the source capacity.

5 Answers   TATA,


How do u analyse protection fault when vcb tripping on load

0 Answers  


How much current does a motor take in no load condition?

6 Answers  


which pump used in STP

0 Answers   Dalkia,


block diagram of 2 ups system connected in parallel mode?

0 Answers  


Hi,I am working in abroad for more than 3 years in a company operating with 11kv and 6.4 MW power. I need c licence in India,can I? some other says only i can get if i work for 2 years in india only! anybody kindly clarify by doubt.Thanks

0 Answers  


why the earth is taken minimum in supplying? wather it the proportional factor to getting work any equipment or a power plant?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)