Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


TO operate transformers in parallel, vector symbol of the
both should be same.If one transformer name plate is not
there, how can we conclude that whether the transformer is
having the same vector symbol or not?

Answers were Sorted based on User's Feedback



TO operate transformers in parallel, vector symbol of the both should be same.If one transformer n..

Answer / guru

Check the vector group by carrying out VECTOR Group testing
( By Injecting a 3 Ph 440v or 230 V to the primary windings
and check the voltage between the terminals in secondary
side)

For each vector group there are standard values which has
to come in the secondary side

Is This Answer Correct ?    1 Yes 0 No

TO operate transformers in parallel, vector symbol of the both should be same.If one transformer n..

Answer / rajendran

we can easily find out and confirm the vector group of the
transformer by using the standard test procedures.

Is This Answer Correct ?    3 Yes 3 No

TO operate transformers in parallel, vector symbol of the both should be same.If one transformer n..

Answer / mgalalkhedr

This vector group test is done at site to check if their is
any damage in the windings during transportation and
erection.
3 -phase AC supply is given on HV side. R-Phase HV and r-
phase LV shorted.

Then to qualify the test following conditions are to be
satisfied after measurement of voltages.

nR+nY=RY, By>> Bb and Yb=Yy.

Is This Answer Correct ?    0 Yes 0 No

TO operate transformers in parallel, vector symbol of the both should be same.If one transformer n..

Answer / mahboob

in such acase we can find the vector group by conducting
vector group test the we can proceed

Is This Answer Correct ?    1 Yes 2 No

Post New Answer



More Electrical Engineering Interview Questions

What is Magnetic Current Test of Transformer.

2 Answers  


What is the criteria for selecting the voltage classes of an AC Induction Motor.The KW rating above/below which ht/lt selection is made may be provided in details.

0 Answers   DAE,


explain types of electric welding and its applications

0 Answers  


A 3-phase IM is supplied from 50 Hz system. It runs at speed of 1440 rpm and slip equal to 4 %. Calculate number of pole pairs. A 1 B 6 C 2 D 3

0 Answers  


For these 2 devices what their power ratings are ? 1) single phase : AC 220V & starting amps 3Amps (i.e. starting torque) and the stabilized amps 2A ... For deep freezer 2) single phase : AC 220V & starting amps 2.7Amps (i.e. including the starting torque of a CRT monitor) and the stabilized amps 1 Amps thanks

1 Answers  






How to calculate the time setting for star connection in star delta starter? For example 10KW 3PH Induction motor.

0 Answers   Taj Group, Tata Steel Limited,


Why the meters sonnected to metering core of CT are not damagedon event of a fault??? Explain the phenomena??

1 Answers   Schneider,


explain the types of drives

0 Answers  


when we connect a CT in the line will there be any loses in the line due to the mutual inductance of the CT.

1 Answers  


when we connect the capacitor bank in series

2 Answers  


What is the need for checking knee point voltage for CT's?

1 Answers  


Is there any specialised book to refer about fault level calculation both in MV and LV side??

0 Answers  






Categories
  • Civil Engineering Interview Questions Civil Engineering (5076)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4445)
  • Electrical Engineering Interview Questions Electrical Engineering (16606)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2992)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (123)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1378)