During he starting up of the motor, the upstream's MCCB (350A) always tri

During he starting up of the motor, the upstream's MCCB
(350A) always trips due to the UVT relay activated.
Can Star-delta starter use for a 20kW Motor (For a powder
mixer machine) cause voltage-dip in the supply line voltage?
If so, what are the recommended solution to
eliminate/reduce the transient voltage dip in the line
voltage?

Question Posted / gkl

4 Answers
7130 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

During he starting up of the motor, the upstream's MCCB (350A) always trips due to the UVT re..

Answer / tushar patil

yes u can use star delta starter
20KW means 30HP motor
u can use VFD (variable frequency drive) also
it is very easy to u
if cable length is more than 50 m then u should connect output line chock to output n input line also connect line chock..
n increase accelaration time in vfd

Is This Answer Correct ?

0 Yes

0 No

During he starting up of the motor, the upstream's MCCB (350A) always trips due to the UVT re..

Answer / piyush rana

You can check the length of the cable from the supply to
motor, I think It will be more so that due to line
resistance loss during starting the line voltage will go
down for the fraction of seconds.
please mention the connected load, transformer capacity,
volatge incoming etc for further clear answer.

Is This Answer Correct ?

0 Yes

1 No

During he starting up of the motor, the upstream's MCCB (350A) always trips due to the UVT re..

Answer / abdulsubur

up to 3kw Dol startor
up to 7kw we can use Star delta startor

Is This Answer Correct ?

2 Yes

3 No

During he starting up of the motor, the upstream's MCCB (350A) always trips due to the UVT re..

Answer / abdulsubur

upto 35kw motor u can use star delta

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

what is different between auto transformer and vriac

4 Answers

What are the rating wise protections required for Generators from 600KVA to 2000KVA

3 Answers

for preparation of design note of 11 / 220 kV , 3 phase, 63 MVA transformer how can calculate or consider the iron losses and copper losses

1 Answers

please forward me the type of questions which would rise while me attending to 33KV Electrical License to my mail ID:vadrevu_raghava@yahoo.co.in

0 Answers

how we calculate torque ? how we improve it ?where torque will either motor or generator ?

0 Answers Reliance,

I have 500A load (WHICH IS SEPARATE MDP PANEL),an MCC panel with 4000A Breaker.Already I have 2500A load.Can I connect this load directly to the Busbar since I have PROTECTION IN MY MDP Panel ?

4 Answers

Draw the wave shape of armature current in a generator subjected to a sudden three phase short- circuit at its terminals. Define various reactance of generator from this wave shape.

0 Answers VECL,

what is recovery voltage & transient voltage ?

1 Answers Bhel,

How much KVAr bank reqired for 630 KVA transformer on full load for maintain power factor upto.99

4 Answers Dhanalakshmi Industries, DLF,

purpose of breaker contact multiplication relay?

5 Answers ABB,

I would like to install the largest KW alternator to a 200 amp aluminum bus box in my home. Is it possible to install a 250 KW 400v 251amp synchronous alternator to my home?

2 Answers

What should be cable size for 75KVA 380/220 3ph transformer

3 Answers

For more Electrical Engineering Interview Questions Click Here