Answer / laxmi kumari & wahid hussa

minral oil.

oil is used in transformer for insulating & cooling purpose.

Answer / jayesh pillai

oil used in transformer must be for
insulating
cooling
having high dielectric strength
bdv must be higher than 45kv
low viscosity oil

Answer / dhananjay kumar

THE OIL USED IN TRANSFORMER IS INSULATING(MINERAL) OIL.THE ASKAREL AND PYROCROL IS TWO INSULATING MINERAL OIL WHICH PROVIDE COOLING AS WELL AS INSULATION FROM WINDING

Answer / raj aamath

transformer oil should have high dielectric strength so we can not use mineral, animal,and vegitable oil becoz the dielectric strength of these oil are very poor.so we use polynor or silicon oil which have high d.s.

Answer / nissan patel gujarat

Insulating oil in an electrical power transformer is commonly known as Transformer Oil. It is normally obtained by fractional distillation and subsequent treatment of crude petroleum. That is why this oil is also known as Mineral Insulating Oil. Transformer Oil serves mainly tow purposes one it is liquid insulation in electrical power transformer and two it dissipates heat of the transformer e.i. acts as coolant. In addition to these, this oil serves other two purposes, it helps to preserve the core and winding as these are fully immersed inside oil and another important purpose of this oil is, it prevents direct contact of atmospheric oxygen with cellulose made paper insulation of windings, which is susceptible to oxidation.
Generally there are two types of Transformer Oil used in transformer,

1. Paraffin based Transformer Oil

2. Naphtha based Transformer Oil

Answer / murugesan

insulating oil use the transformer

Answer / sagar khandey (r.c.e.t, bhila

1.INSULATING OIL IS USED IN x-MER.
2.The oil should be greater than 100M Ohms resistance.
3.we can't define its BDV value, without knowing its rating.
for Example:
MINIMUM BDV in KV RATING in KV
23 KV <69
26KV <69 KV-288KV

26 KV >388KV

Answer / ashok kumar

oil helps cool transformer b/c it also provide part of electrical insulating b/w internal live parts.

Answer / manjunath

Lubricant oil is used in T/F for Cooling Purpose

Answer / ramki

INSULATING OIL

why there is a phase difference between line voltage & phase voltage ?

4 Answers  

what is the tolerance of electrical frequency for India? it's .5% or 1%?

8 Answers   Engro,

Do closed loops systems require manual input?

0 Answers   Ericsson,

why using touble tube lamp use in factory?

3 Answers   ONGC,

Draw a 230kv two-bus bar system showing the following. 1.Two generators (150MW) each connected through one 15.75/230KV transformers 2. 1 outgoing lines 3. Two 230/130 KV transformers 4. BUS PT's 5. CT

0 Answers  

how will calculate the safe starting current of 3-phase squirrel cage induction motor?

0 Answers  

why the single phse machine can not run by the three phase supply.

2 Answers  

What shall be the secondary output voltage if the primary winding of a 220/6V, 50 Hz transformer is energized by an 110V, 60 Hz supply?

0 Answers   HPCL,

Baud rate is used to descrice...?

2 Answers  

ouestion for the post of section engineer

1 Answers   BSNL, RRB,

how to read idmt curva

0 Answers  

what is the knee point voltage ? what is differtial rela? what is impedance and % of impedane? what is the postive phase sequance ? negative phase sequane ? and zero sequance impedance ? what is sortcircuit calculaion? why take calculation? define stabilty test ? why? what sentivity test? define merz protection ? what is the burden ? class 5p10, accracy, metering ct take knee point voltage test thet time what heppan why dont take knee point test to metering ct?

0 Answers