Answer / ss

the potential transformer is used for meetering purpose ,it
is a instrumental transformer it receives a high input but
sends a 110v only for meetering and relay purpose.but incase
of transformer it works step up/down

Answer / kd

Basically both are the same

Answer / mahadevan( auva project co ltd

where we can calculate total summation of charges in the line that is called potential transformer. actually potential which is measured in the open path only as same phenomena of emf(v/m).In the nature potential transformer are not possible to exist.because all measurement taking in the closed loop only.when it's closed loop we measure difference of charge (voltage).

where we measure difference(ex.5v) of positive charge (+5v)one side and negative charge(-5v) on other side can be called as voltage.this phenomena only suitable for all voltage transformer.

Answer / daniel

We need higher precision in the case of Potential
transformer as it is used for measurement. But in the case
of Voltage transformer precession is not the key feature

Answer / ravi teja

P.T are extremely accurate,ratio step down transformer and
are used standard low voltage rating volt meters(100-250)
V.T are used to step-up and step-down the voltage

Answer / anjum

POTENTIAL TRANSFORMER AND VOLTAGE TRANSFORMER ARE THE SAME

Answer / anoop philip

voltage transformer used only for voltage transmission ,but PT used for voltage transmission as well as mettering.

Answer / aman ahuja

THIS IS TYPICAL QUETION... WELL.. VOLTAGE transformer Compare the primary and
secondary voltage ratio of a transformer and to maintain
fixed voltage at secondary terminal, it sense to auto tap
changer of the transformer to maintain fixed voltage during
no load to full load.
Potential transformer is used for measuring heigh voltage.
It's Primery windings is connected to the high voltage
source & secondary voltage is only 110 volts

Answer / liz

hi,i just wanna to asking here too, if our factory using
existing supply 22KV/110V and we want to upgrade their
supply to 33kv,is there neccesary to change our VT/PT/CT?

Thank you

Answer / suri

CT secondary side should be closed whereas in PT may be open
or closed.
CT should connected in series with the line and PT should
connected across the lines.

how will be power factor while using the resistive load and Capacitive load?

3 Answers  

We have 3 Gensets 1.500kva,2.380kva,3.250kva How can we connect in common busbar&we have variable load.

4 Answers  

Give accurate definitions for these electric terms: Inductor Inductance Inductive Induction Reactance Reactive Esam Baraka ٢١ ساعة

0 Answers   HMK,

Tell me about yourself. ……………………………………. Why did you leave your last job? What do you see yourself doing five years from now? Ten years from now? What are your long-range career objectives? Why did you choose this career? How well do you work with people? Do you prefer working alone or in teams? How would a good friend describe you? What would your last boss say about your work performance? Why should I hire you? What makes you qualified for this position? What do you think it takes to be successful in a company like ours? In what ways do you think you can make a contribution to our company? What's the most recent book you've read? What two or three accomplishments have given you the most satisfaction? Why? Describe the most rewarding experience of your career thus far…………… Why did you decide to seek a position in this company? What can you tell us about our company? What do you know about our competitors? What two or three things are most important to you in your job? Are you willing to travel for the job?

0 Answers  

what will be the effect of leading power factor on turbogenerator (and system) that is running parallel with other TG.

1 Answers  

AMF (auto mains failure) control for DG sets at home.

1 Answers  

WHY DO VOLTAGE TRANSFORMERS FAIL DURING EARTH FAULT IN THE DELTA CONNECTED 6.6KV ELECTRICAL SYSTEM

0 Answers  

what is the diference between the 4pole & 6pole DC Motors & what is advantage 6pole over the 4pole ?

0 Answers  

what is a switchgear. what is its work & where it is used?

5 Answers  

What happens if we give ac supply to dc shunt and series motors individually

4 Answers   Essar,

What is the minimum permissive IR value for LT & HT motor for safe starting?

1 Answers   Rukmani,

Match the following a)(X'+Y') b)X'Y' C)XY 1)NAND 2)NOR 3)Carry

0 Answers