Interested to Buy Any Domain ? << Click Here >> for more details...
In a coal fired boiler furnace temp. is high but super
heater out let temp. low what reason for this?
- 6 Answers
- 13884 Views
- ABB, Essar, Gayatri, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Two reason
1. Scale deposit inside the boiler & superheater tube,
2. Soot deposits outer surface of boiler & superheater tube,
| Is This Answer Correct ? | 16 Yes | 2 No |
Answer / ritesh patel
The specific heat of water is higher
than that of air.
| Is This Answer Correct ? | 5 Yes | 3 No |
Answer / y v subba rao
Final super heater inlet steam temperature is well below than flue gas temperature of that zone(400degrees). Steam travels trough super heater coils with higher velocity(may be 25m/sec) as per the boiler design to meet the steam requirement of turbine. Hence the pretension time of steam is very less in super heater zone. More over there is always a temperature difference across the tube thickness. Due to this reasons super heater out let steam temperature is always much below than flue gas temperature in that zone. However the boiler itself will be designed in such a way.
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / pradeip
because we designed boiler like that, what temperature we
require.
| Is This Answer Correct ? | 1 Yes | 3 No |
high cal value of coal is also the reason if we use high
amount of petcoke then furnace temp high but boiler outlet
steam temp not high
| Is This Answer Correct ? | 0 Yes | 4 No |
Answer / k.p.selvakumar
1.super heated coil have any leak or puntcure.
2.continousely opened condition of attemperator valve.
3.opened all turbine draine valves in trip condition.
4.forced draught fan tamper open value high.
5.operating problem having in super heater outlet valve to main sream line.
| Is This Answer Correct ? | 0 Yes | 5 No |
How to calculate boiler capacity? I have 1 Autoclave, Which has to use for AAC block. Dimension for this Autoclave is - 13 Meter Length & 2.2 Meter Diameter.
Why reheater is not used after IP turbine.
What is difference between secondary Air & Tertiary Air and Their use.?
Can any one advised me how we can measure the losses in a 11kV/415v power transformer? We have no access to the incoming mains into the primary of the transformer. Can one derive something useful by measuring temperature rise in the transformer?
What happen when the AVR of the generator fails? Will it cause power instability and total failure of the alternator?
Need of oxygen dosing in super critical powerplants?
.What are the equipments should run when there is a black out in power plant.
Why cold water is used for Boiler Hydro test
Qatar Fertiliser Company (QAFCO) Shortlisted me for interview (got the intel from my source) for Field Operator- Utilities post. Please let me know what kind of questions they asked? ... this position requires 5 years of experience in Power Plant and background Diploma in Electrical/ Mech. ... my Background is Electrical and I am a sub Assistant Engineer (Operation) at a private HFO based Power plant... PS: Please Let me know what preparation should I take to obtain the Interview which will be take place In Bangladesh soon
whatis means of PPA & FSA OR SFA in power plant operation
operation
what is block out in thermal power plant?
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
