We have laid the single core Armoured cable 7 nos ( 2 each
phase & 1 neutral ) to cater our electrical load .
the issue is though we have Glanded the cable both the end
also givan the earthing to the panel both the end we are
facing a heavy sparking at the gland side. what could be
the reason.
- 12 Answers
- 17333 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / shantanu mishra
This is definitely a case of improper earthing. The
substation earthing is poor. The panel and armoring of cable
need to be more strongly earthed. During normal conditions
there would not be any sparking butwhen there is any fault
on 11kv line nearby, the ground potential suddenly rises and
so the panel comes at a high potential and sparking take
place between panels and armoring of cables which are not
getting proper earth.
| Is This Answer Correct ? | 2 Yes | 1 No |
Answer / shantanau mishra
Dear Virendra
have you found any solution to your problem. Pl share.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / ahmed
Well,you need to check if you really need to glad the
cables from both side .Or check the type of glad is it
metal or non-metalic .
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / rajesh
Use special gland (Gland with bush) at the panel(load side), but ensure the proper gland earthing in first side. The above situation is due to circulating current
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / abhishek mishra
Dear Virendra
if you are using CRCA gland plate for glanding then such problem may occur. If you are using single core cables then either use aluminium gland plate or make a thin cut hole to hole in CRCA gland plate
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / robertm
It sounds like you have a loop, check and see if the
neutral and the earthing cable are laid down on the same
bars. If this not the incoming service then that could
cause your problem.
| Is This Answer Correct ? | 0 Yes | 1 No |
Guys,
let me clear that the earthing is proper we get the value
0.1ohm. We have used double compress gland which is fixed
in proper way, there no such thing like looping, but still
the problem is there . please share what else can be the
cause ?
| Is This Answer Correct ? | 0 Yes | 1 No |
In EDO ACBs what is a purpose of closing coil and motor, what is the operation of these devices are they inetconnected. means if we give supply to motor and by BCS we charge Closing coil,what exact is operation is and how it charge a spring of ACB. Sir if anybody has an wiring diagram please send me the link to operate and EDO breaker.
What is the importance of setting TSM & PSM?
1000 W bulb takes 4.16 Amps at 240 volt then what will be the KWH & if i am using 1000 W bulb at 180 Volt the amps will be 5.55 then what will be KWH????????????????
what u meant by shock ? whether it depends on voltage or current
Why we are mention U1, V1, and W1 in primary side of transformer give technical reason
What is the basic working principle of Tri vector meter?
What is C curve and D curve of MCB?
What are the limitations of Kirchoff's laws?
what is the difference between Miniature circuit breaker & motor control circuit breaker ?
what is maximum demand.
how to make parrallal ups
Can a dc motor works as a dc generator. If yes , then how?
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
