Answer / s.prabhakar

pile foundation is a type of deep foundation which is used
at low bearing capacity soils such as clay silty sandy
soils to transmite the load of the structure above ground
level so that setliment of struture is minimal. These are
generaly two types, i,e friction pile & End bearing pile.
As per indian standard codes setliment should not be more
than 11mm after test loading

Answer / kamal mahato

Pile foundation is the type of deep foundation. It transfer
the superstructure load to the hard strata i.e. toe level
of pile foundation. Generally it used where the bearing
capacity of soil is low eg soft soil, water table high area
etc.

Answer / farooq

pile foundations are one of the types of deep foundations.
they are used in case soft/silty/clayey type of soils.
As in such case of soils going for normal foundations may
not be possible either from economical point of view or may
not be possible at all in case u want to construct near
seashore etc.,
these are the foundations which transfer load to greater
depths, where there is strong strata / load reaching that
point is minimal.
these are pipe shaped, we have different types of pile
foundations.

Answer / anuj kumar

pile foundation is a type of deep foundation used in a case
of silty,soft and clayey soils which are driven or hammered
through the soil to a considerable hard strata beneath soil
surfaces and transmitting top and minimal loads of super
structures into the ground.These are generally used where
soil is not having good bearing capacity at lower depths or
is not at all present at lower depths as in the case of
houses constructed over submerged area.

Answer / kumar j

Pile foundation is a type of deep foundation which is
used
for structures where the loads are to be transmitted to a
point some distance below ground level.

Answer / rahul shukla

It is the type of foundation which can resist the entire
load of structure or transfer the load of structure which
located at more depth.

Answer / s.iyyappan

pile foundation is one of the best foundation. Basicaly it
carees the load from the structure and distributed
uniformaly to the ground. Exspecialy in seashore side it
resist the uneven settlement in structure

Answer / santosh

pile foundation is the type of deep foundation where the
load transfered below the deep soil strata.load transfering
can be done following two way
1 end bearing of piles
2 skin friction
3 composit method

Answer / lekhani dasanayake

a pile can be loosely defined as a column inserted in the
ground to transmit the structual loads to a lower level of
subsoil. classification
1.end bearing
2. friction
displacement piles
1.timber pile
2.precast concrete piles
3.preformed concrete piles
4.steel performed piles
5.composite piles
replacement piles
1.percusion bored piles
2.rotary bored piles
3.prestcore piles

Answer / yas

pile is used to transmit load form structure to earth.

how the centre of gravity is used in construction?

1 Answers  

For making a new road in a village having a school & hospital , tell the steps of construction systemically ?

0 Answers   UPSSSC Uttar Pradesh Subordinate Services Selection Commission,

how to calculate cement coefficient for 20mm thick vitrified tiles flooring with cm 1:4 with explaination

4 Answers   Kicons, Marg,

What is the formula for figuring out how many gallons of water are in a pipe by the foot?

0 Answers  

Define What is passive earth pressure ?

0 Answers  

how do you calaculate the total steel quantity of an rcc building using thumb rule?

0 Answers   L&T, SSC,

for gravel roads in India to get 1feet height how much height we have to fill

0 Answers   Sunrise,

strength vs shape factor

0 Answers  

How to activate isometric axes in cad?

0 Answers  

1) what is the seewage discharge per person per day taken for design purpose as per IS codes? 2) how to convert gauge to MM like if we measure 18G as our door frame then how much is it in MM ? 3) how much binding wire is required ti tie 100kg steel ? 4) while making rings in steel reinforcement , whether the corners of rings are deducted to take out cutting length ? 5) how much carbon content should be there in steel used for construction purpose? 6) what are fe415 & fe 500 and which bars are used in general civil works?

1 Answers  

mean of NH4 pipe

1 Answers   GVK, L&T,

Mujhe koi ye bta do ki 1.54 hi ku lete h material ki quantity niklne ke liye Sab jgha dhund liya bt samj nhi aaya mujhe koi alag aalag krke smjao ki cement m aggr. Dust m itne % wet or dry % hoti h fir kaise kaise 1.54 aaya kha se aaya smjao koi pls m confuse hu my calling nd wts app no. Is +919034604938

2 Answers   ADP,