Answer / avinash km

Rtcc means remote tap change controllers which are used for tap changing of ht side of the transformers which are having on load tap changing system, so that output voltage can be raised or lowered.

Answer / kuresh

RTCC means relay tap changer circuit,these are the relay
which give command to the tap changer present in the
transformer H.T side to either increse or decrese the tap
since due to inductive load ( lagging p.f ) , the secondary
terminal voltage would decrease which would not be good for
the loads so by chnging taps, we increase the primary
voltage which in turn changes the secondary
voltage,normally done

Answer / kishore kumar balligavi

RTCC Mean (REMOTE TAP CHANGER CONTROL) it use increse the voltage total 17 tap 1 tap increse the 3 or 5 volts

Answer / naveenkumar

Rtcc means remote tap changing circuit. And required for
Changing the tap at the hv side of the transformer online
If the lv side voltage of the transformer fluctuate
Because of load. It has avr (automatic voltage regulator)
To control the tap changing.

Answer / birendra

RTCC (REMOTE TAPE CHANGING CIRCUIT).IT IS USED TO AUTO
STABILIZE THE OUT PUT VOLTAGE OF A TRANSFORMER.IT CAN
CHANGE THE INPUT TAPPING OF A TRANSFORMER ACCORDING TO THE
SET VOLTAGE VALUE.

Answer / viraj

As load increases or decreases according to that Tap of OLTC shoul be change for maintaining the voltage level of feeder,so RTCC(remote tap changer cabinet) will remotely operate OLTC.

Answer / rukhiya fahmidha

RTCC is a tap changing control which is used for the parallel operation of transformer

Answer / murali

RTTC means remote tap changing control it is used to
command the OLTC panel control the primary side of
transformer . When we required constant voltage it is required

Answer / riyaj naikawadi

RTCC meance - Remot Tap Changer Control.It is a voltage
control station of Transformer, It works as a Voltage
regulator & give command to the OLTC.

Answer / vrt

it is a decorating device that;s all

what is difference between AC VVVF drive & Dc VVVF drive explain their working principle?

13 Answers   Apollo, OPS,

What is an Antipumping relay ?

4 Answers  

Instrument connected to a single phase supply

1 Answers   Alstom,

why not phase to phase fault occure in raining day in hv sub-station?

1 Answers   Getco,

WHAT IS PRINCIPLE OF TRANSFORMER

10 Answers  

As we know multiplicity factor derivation equation is as below MF = main c t ratio / main p t ratio * meter c t ratio / meter p t ratio * meter dial constant Where in digital meters for HT kwh import export now a days meter constant are calibrated already which is 1 So my question is For HT 11kv 110 v line values are as below Main c t and p t ratio are 11000 v and 110 v and 20/5 means 20 amp and 5 amp Now meter values are 11000/√3/110√3 and primary and secondary amp are displayed as -/5 amp on kwh meter so what will be the MF for this meter ?

1 Answers   NEPC,

On a 10 KVA UPS we have to provide a DC MCB for Battery bank of 16 nos (12 V 65 AH). What Shall be the current rating of DC MCB ?

6 Answers   RR, TNEB Tamil Nadu Electricity Board,

725KW Three DG set Synchronised but DG no-1 power showing 750KW DG n0-2 power showing 500KW DG no-03 showing 500KW. DG is Shynchronised but why this different power showing?

3 Answers  

Whar is the KvA rating of 33Kv substation & actual kv rating of power generaating station.

1 Answers  

Why squirrel case induction motor bar is skew permanently?

1 Answers   Nesco,

I have one ct of ratio 3000-2000/1 Amp its knee point voltage mentioned on name plate is 500-333/30mA-50mA at Vk/2. in secondary box there is three terminal named 1S1, 1S2, 1S3 then on which terminal obtained the knee point voltage ie 1S1-1S2 OR 1S1-1S3 & also specify the knee point voltage for the ratio 3000 from name plate.

1 Answers  

How can you calculate the size of the down conductor cable for the lightning protection system. Is 70mm2 cable can replace 95mm 2 bare copper cable when the copper tape size is 25Wx3 thk mm.

1 Answers