How to calibrate the magnetic flow meter and how to correct
the flow if it is showing more flow.

Answers were Sorted based on User's Feedback



How to calibrate the magnetic flow meter and how to correct the flow if it is showing more flow...

Answer / maneesh

if the instrument is online calibration can be done by
closing the valve at downstream side.now the meter should
read zero if not recalibrate it.always remember while
calibrating magnetic flow mwter the meter should be filled
with fluid and fluid should be condectieve

Is This Answer Correct ?    21 Yes 4 No

How to calibrate the magnetic flow meter and how to correct the flow if it is showing more flow...

Answer / r.ravikant

There is constant factor for every correspondence flow.
For example,in Krohne Marshall Magnetic flow transmitter
ther is 'GF' factor fix for correspondence flow,so use this
factor.

Is This Answer Correct ?    17 Yes 8 No

How to calibrate the magnetic flow meter and how to correct the flow if it is showing more flow...

Answer / muzaffar ahmed

if the instrument is online calibration can be done by
closing the valve at upstream and downstream side.now the
meter should be
read zero if not recalibrate it.always remember while
calibrating magnetic flow meter the meter should be filled
with fluid and fluid should be conductive.
and other wise condition as such so you should be done by
analog to digital trim.

Is This Answer Correct ?    3 Yes 1 No

How to calibrate the magnetic flow meter and how to correct the flow if it is showing more flow...

Answer / muaz

i ewi


i want to know about supperssion and elevation

Is This Answer Correct ?    2 Yes 3 No

How to calibrate the magnetic flow meter and how to correct the flow if it is showing more flow...

Answer / uc nayak

Magnetic flowmeter calibration method is only by taking known volume of flow through it by taking drop test method.Other than this you can simulate the flow convertor with specific simulator with spefic simulation factor only.

Is This Answer Correct ?    0 Yes 1 No

Post New Answer

More Instrumentation Interview Questions

I am manjunath having exp in maintenance of chemical plants,know i want to do a design course INTOOLS,after doing design course can we get jobs in design field.sinve i dont have design exp..

0 Answers  


how to test rotor &stator earth fault in turbine

1 Answers   Bhel,


whats the diff b/w zero pressure and obsolute pressure

4 Answers  


How to do ma trim in massflow meter?

2 Answers   Pakistan Steel,


In control valve , Failure position : Close If it is Fail close(FC) during failure of AIR.. what will be the initial/ normal position of control valve is it normally open or close? please some one explain soon..

2 Answers  






The DCS has the following signal type:

3 Answers  


Ple give me "INDUSTRIAL INSTRUMENTATION AND CONTROL S.k. Singh 3th edition" Solution manual to self-Check Quiz and chapter-wise PowerPoint Slides. Home web-site not available... Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Ple Thanks for all...

0 Answers  


how to calculate orifice sizing? and tell me if pipe size bet 50mm t0 200mm then we can use pipe flange??? and above 250mm pipe size should i use D & D/2 Flange? is it right or wrong?

0 Answers  


What is PDS and PDMS ?

0 Answers  


Draw a simple circuit for a well head control panel used to protect the well against fire, leak, blockage, ESD, & controls the operation of one downhole & one surface safety valve. Explain the operation and controls

0 Answers  


which are types of orifice tap ?

2 Answers  


How many ohms are required for proper earthing?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)