What will happen if 230V DC motor connected to 230V AC
Supply?
- 15 Answers
- 57901 Views
- Ashok Leyland, BOC, JSW, ONGC, RRB, TRB, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
These are the effets produced when a DC motor connected
with AC supply:
1.Rotor speed will be less than the rated speed.
2. Rotor produced less torque and max. will be very less.
3.Core and copper loss will be more.
4.high sparking at brush, there by reduced life.
5.Motor gets heated up easily.
| Is This Answer Correct ? | 156 Yes | 13 No |
when a dc motor is connected to a ac supply it will run
with reduced efficiency.in case of ac reactance will comes
into picture.so,increased losses due to inductance.and
there is sparking at brushes.motor will run with reduced
speed.
| Is This Answer Correct ? | 83 Yes | 22 No |
Answer / infodoss
DC series motor can rotate but less speed compare to DC
supply
| Is This Answer Correct ? | 53 Yes | 27 No |
Answer / anand
actually motor will be damage for giving ac supply...speed
of the motor decreasing, sparking at brushes,then get
heats...in case dc series motor wil run without less
problem ....bcoz series motor os a univresal motor.....
| Is This Answer Correct ? | 26 Yes | 6 No |
Answer / n nagaraju
HEAT GENERATING IN THE MOTOR THEN MOTOR SHOULD BE DAMAGED
| Is This Answer Correct ? | 15 Yes | 7 No |
Answer / shrikanth
Motor runs with a speed less than its rated speed, sparking in brshes.
| Is This Answer Correct ? | 11 Yes | 4 No |
Answer / pavan
Rotor speed will be decreased.
It produces a less torque.
Losses will be more
| Is This Answer Correct ? | 10 Yes | 5 No |
Answer / r.s. kushwah
motor will produce less torque, spark on commutator,
| Is This Answer Correct ? | 5 Yes | 1 No |
Answer / parikh snkp
it will work...coz in the nextcycle both field and armature winding both will be in reversed direction so by this we can get same side rotation ........i mean to say unidirectional rotational
| Is This Answer Correct ? | 3 Yes | 3 No |
what is the unit of electricity????????????
When testing an earthing connection, we use a 60 or 100 candle bulb with a phase connected direct from supply and the other wire to the new earthing provided.If the bulb glows then the earth is ok.Else earth connection is not Ok. So, why dont we can use all the home appliances taking a single wire from the phase and the return connection to Earth instead of return connection to neutral?
What is the settings of distance protection relay in 400 kv line
what is the difference between analog and digital signal?
my motor rating is 800HP, 128Amps, 3.3kV. What is capaitor bank i can use for PF improvement to 0.990?
Why we does earthing for transformer neutral point
Why using synchronising methed in DG's sets?
in conclusion why we select you?
What is the difference between Type test and Routine test?
What is the difference between synchronous asynchronous memory?
why the Current transformers secodary is shorted to ground (In metering and Protection)
WANTCONTACT NUMBER & EMAIL/ WEBSITE TO CONTACT THE SECRETARY,MADHYA PRADESH LICENSING BOARD(ELECTRICAL),K- BLOCK,3RD FLOOR,SATPOODA BHAWAN,BHOPAL
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
