Answer / laxmidhar ,nmiet bbsr

we need,
miliamp source(giving supply to i/p)
i to p converter(pressure signal to control valve)
air supply(for input to i/p and control valve)
multimeter(miliamp check)
small screw driver(for adjust zero and span)
and check

4ma for 0
8ma for 25%
12ma for 50%
16ma for 75%
20ma for 100%

Answer / ramkumar

We can calibrate the Controlvalve by using the mA feeder
(make-DRUCK).while calibrating the I/P using mA calibrator
error occurs adjust Zero and span in the I/P .

Answer / uprabhagaran

MA sourse

Answer / zuheir beilouni

Use a current source to calibrate the I/P converter error ,
but if the error was in the valve , calibrate the valve
positioner using Wallace and Tiernan calibration box or for
fast calibration couple a monostat gauge to calibrate and
if both were ok problem lies in the solenoid then check the
supply to it

Answer / biju

We can calibrate a control valve by connecting a HART/FF
communicator to the valve and then doing Autocalibration
through the instrument...

Answer / mustafa ahmad

mA SOURCE & HART COMMUNICATOR WILL USE FOR THE CALIBRATION
OF CONTROL VALVE .WHEN U CALIBRATE THE CONTROL VALVE THAT
TIME U FOUND ANY ERROR . YOU DO AUTO CALIBRATION BY HART
COMMUNICATOR . WHEN AUTO CALIBRATION WILL FINISH , YOU DO
THE STROKE CHEK BY HART COMMUNICATOR OR mA SOURCE

Answer / dhanasekaran c

Depends upon the valve. Pneumatic calibrator for 0.2to
1.00kg/cm2 Valve.For Electronic positioner( 4-20ma) We can
use Loop calibrator. For Smart type of positioner fixed
valves smart calibrator 275 or 375 or 475(latest) must be
used. Field bus MC5 hand held calibrator can be used.

Answer / antionyo

control valve calibrator

Answer / abinecious

SCANDURA

Answer / janardhan reddy

we can calibrate the control valve by using the dead weight
tester and transmitter and pid controller,

I HAVE PRESSURE TRANSMITTER WITH TWO WIRES 24 VOLTS SUPPLY.IF TRANSMITTER WILL GIVE SIGNAL TO THE DCS WHAT HAPPEN TO THE 24 VOLTS POWER SUPPLY IT WILL DROP OR REMAIN TO 24 VOLTS POWER SUPPLY.

3 Answers  

Furnace draft transmitter range is -50 to +50 mmwc. why the impulse line connected in hp side?

2 Answers   Arena,

what is mean by hot loop and cold loop testing, whts different between both

2 Answers   Honeywell, PDO,

please tell me how to convert double acting ytc positioner yt-1200 into single acting ytc positioner ?

1 Answers  

What is minimum distance between three thermocouples (2oo3) mounted on same pipe line (20")? Technically accepted by stright line mounted or circler mounted?

1 Answers  

What is the procedure of DP switch calibration 

2 Answers   NOCL,

What is difference between reset and initialization in system.

1 Answers   Marafiq,

I am pujita completed Electronics and Instrumentation Engineering.As a fresher i am going to attend the interviews.Could anybody guide the topics/questions covered mostly in interviews.

11 Answers  

What is CNC

1 Answers  

Tr. Wiring for calibration.

0 Answers   CCIE,

tell how to calibrate a magnetic flow tx, vortex flow tx,dp flow tx,nozzle flow tx and venturi flow tx?

2 Answers   TATA,

In dcs contol valve parameters showing like this Gain=1 or 2 , ti=7 sec, td=20sec. But temp,pressure,level control valves we are using in which type parameter side using ti,td clearly tell me

1 Answers