Answer / realas

The cable derating factor is the reduction from its present
capacity for a certain gradual amount due to intermittent
ambient temperature, insufficient space, unbalance flux,
higher voltage dropped, depreciation, etc.

To minimize the cause and effect conduct proper survey and
proper wiring to withstand on the cable loads and locations.

Answer / nid

derating factors are differ with the bunching of cables for
single layer it is .9
double layer .71
tripple layer .62
4 layer .56

Answer / viral

Due to partial discharges in cable it can't be utilized to
it's rated capacity.
As current flowing to charge cable capacitance is extra
burden on that which will make it to carry less current for
load.
To reduce this good insulation material should be use.

Answer / jagadisha.n bmsit

Loss of Dielectric strength of cable is the derating factor
of cable.... It can be minimized by selecting the proper
rating of cable with operating conditions and proper
maintenance of cables

Answer / chirag

Derating factor is very useful thing for selection of cable
when it is necessary to laying in air, duct or ground. wIt
depends on the ambient temperatre

Answer / viswanathan.

For obtaining a desired current at the utilisation end of a
cable irresponsible to the rated current carrying capacity
of a cable, many factors to be consider which tends to
reduces the current carrying capacity of a cable. viz
length of cable, connected equipment, inductive, capacitive
loads, etc. these factors will increases the actual current
and desired size of a cable.

Answer / yogesh zambre

Due to partial discharges in cable it can't be utilized to
it's rated capacity.
As current flowing to charge cable capacitance is extra
burden on that which will make it to carry less current for
load.
To reduce this good insulation material should be use.

Answer / mohamed abd elhamid elsaied

Due to partial discharges in cable it can't be utilized to
it's rated capacity.
As current flowing to charge cable capacitance is extra
burden on that which will make it to carry less current for
load.
To reduce this good insulation material should be use.
and this mean that if cable can its rated 100 Amp. it will
max amp 95 Amp.

whenever a squirrel or a crow gets tangled near the out put of the feild transformer there is a discharge of 440 volts of current through the neutral due to which my appliances blow up causing a huge bang.will the RCCB help in these conditions

1 Answers  

why field resistance is higher than armature resistance in dc machines? and why filed resistance is kept at min value at starting in same time of armature resistance at max value?

4 Answers  

before transformer oil dielectric strenght tests are taken the oil should be allowed to settle to remove option 1 air bubbles 2 gasses 3 contamination 4 water

0 Answers  

What is the LUX

2 Answers  

which motor is used in high mast ( street light) & give the hight of tower .

2 Answers   Construction, Honda,

what is mean by marshalling box in transformer?

8 Answers   Reliance,

i have attended the interview on 4th June,08 at Kolkata in IOCL, can anybody tell me what is its result

0 Answers   IOCL,

technically, what is the reason behind starting the motor star the delta connection .. and what other ways to do this rather than using " star-delta transformer"

0 Answers   Wipro,

A 500 V shunt motor runs at its normal speed of 250rpm when the armature current is 200A. The resistance of the armature is 0.12 Ω. Calculate the speed when a resistance is inserted in the field reducing the shunt field to 80% of normal value and the armature current is 100A.

0 Answers   VECL,

WHAT IS VCB SAFETY

0 Answers  

how we are desining 63.5 ohm resistor for NGR of alternator?

1 Answers  

How do we calculate Blower drive Power (kw) If we have Volume m3 and Pressre (mmWC)

1 Answers