Answer / udayakumar

starer is eused for aeasy to opearate the motor,and
difrend methed of controlling

Answer / tony

you can follow this link http://tonysblog.in/dc-motor-and-generator-basic-principle/

Answer / md.azizur rahman

Electrical starters are generally used to limit the sarting
current of the inputed voltage to any d.c. motor. when
voltage supply is given to a d.c.

Answer / prithwis jana

1)Protection of the motor.
2)When there is power cut the starter willbe off automatically.But when power will come then starter willbe started manually for humen safety,otherwise the motor will start automatically.May resulting in accident to humen life and property..

Answer / shashikant mahajan

At starting of motor it can't have back emf & winding resistance is very small, so armature winding takes 15-20 times more current than full load current due to which torque developed is proportional to Ia and which is also 15-20 times assuming shunt motor operation.Due to such a high torque,shaft & other accessories are subjected to mechanical stresses these stresses may cause permanent mechanical damage to the motor.
To restrict such high current at starting, the variable resistance(starter) connected in series with armature. at the beginning the entire resistance connected in series with armature & cutoff gradually with speed of motor.
i.e. starter works as a current limit device at starting of motor.

Answer / milinda4p

at the moment of start there is no rotation of the motor. So there is no back emf present. So the full voltage is applied across the winding so the current is higher( at the moment of start). In this case the starting current is more than 6 times the rated current. So the motor consumes more apparent power( for most of the industrial motors this is measured normally in kVA and metering is carried out for this seperately called maximum demand measuring. This is costed in Rs/kVA and rate is pretty much higher (In sri Lanka Rs 1000/kVA) So due to not using a startor for a motor can cause for much higher electricity bill.

Answer / nandkishor yadav

3 point ; 4 point ; thyristor control only for dc motors
direct online and star delta for ac motors.

Answer / aakash5994

Starter is not always used for limiting starting current as dol starter doesn't reduce starting current.
There are many other uses of starter:
1. For motor control from DC's
2. For providing protection against under voltage, over voltage, over current, overload etc

Answer / mani

if the motor stating torque is low then starter is used to start the motor

Answer / basavaraj

Starter used for start & stop the motor and redusing the
starting current

Explain the Term in CT Name Plate – Class: 5P10

6 Answers   Jindal, SRES,

Why single core cable required bonding at double end.

1 Answers  

What is the difference between Neutral and Earth

6 Answers   Bhel,

what will happen if ac motor given dc supply?

1 Answers  

If stator & rotor of a 3-phase induction motor have different no. of poles, will the motor run or not??

3 Answers  

I need to connect a synchronous generator to the grid using automatic synchronization and two circuit breakers (one for synchronization, one for end connection to the grid), how to determinate the required diameter of the cables?

0 Answers  

if we have to design a small transformer of rating 1 kva or 1 mva , how can we design it?

1 Answers  

Dear All please ive me ur ideas... What is the major diff between cu conductors and Al conductors ?

3 Answers   MX Technology,

What is MS-EXCELL?

0 Answers   NTPC, Siemens,

What is the procedure/activities to be taken to inject the current more than 2000A by using 2000A Loading Transformer?

0 Answers  

what is the meaning of bus bar, in electrical panels.

13 Answers   HLG Habtoor Leighton Group,

Alternator couple to diesel engine why, Alternator couple to ac service motor with gear drive for 1500 rpm possible (yes or no) aim to low input power supply give to motor then high output power taken for alternator Please answer this question

1 Answers   Turbo,