I have a 1000 kVA Transformer(11kV/0.415kV) and a APFC panel of 400 kVAR(LT).No

I have a 1000 kVA Transformer(11kV/0.415kV) and a APFC panel
of 400 kVAR(LT).Now if i want to remove the LT APFC panel
and install a HT(11kV) APFC panel on the HT side is the HT
APFC panel will work same as the LT APFC panel(improve the
power factor),if yes what will be rating of the HT APFC
panel?what is the formula to calculate HT APFC panel rating???

Question Posted / kaushik sarkar

2 Answers
9564 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

I have a 1000 kVA Transformer(11kV/0.415kV) and a APFC panel of 400 kVAR(LT).Now if i want to remov..

Answer / k.prakashchandra

The power on HT side is equal to power on LT side +
3%(1.6%). The power rating of APFC remains the same.

Is This Answer Correct ?

2 Yes

1 No

I have a 1000 kVA Transformer(11kV/0.415kV) and a APFC panel of 400 kVAR(LT).Now if i want to remov..

Answer / kathiravan

Since the PF is corrected "before" the bank is connected
(EX:A--------B---------------C----------------D-----------E.
Suppose If the bank is connected the location @"C",the PF will be corrected from location A to C only,where as location C to E will not be effected by the installation of location C)there wont be much effected weather to locate capacitor either primary or secondary of the transformer.Rating of the capacitor must be the respect of HV/LV supply voltage.

Is This Answer Correct ?

1 Yes

1 No

Post New Answer

More Electrical Engineering Interview Questions

what is sevice settings for mccb?How can be it setted?

1 Answers

if there are six generators (3 gas CATT, one Jenbacher o1 MW each, and two nos Diesel 01 no 01 mw other 0.65mw EDGs ( say), 3 CAtt gas set have identical pole pitch,01mw EDG and Jenbacher gas Set have different pole pitch, how their power connection can be done to connect a common bus bar during installation. in short, how different pole pitched generators power connection can be done to connect a common busbar system through generators incomer ACBs.

0 Answers

I have applied the post Junior Engineer-iii(c&w)in R.R.B chennaI recently . can i get any model question paper LAST 4 YEARS?

2 Answers Data Entry Operator, RRB, SSC,

why you don not show protection and type of isolation in key single line diagram?

0 Answers

What type of tranformer generaly at soft wares like capacity 2000 kva 1800 kva etc iam confused it CT or PT OR distribution tranformer

3 Answers

Why generator is not connecting in delta ..why connecting in star ?

4 Answers Bhel, Foretec Engineers,

what is basic difference between the normal tube light choke and electionic choke ?

4 Answers Amaron,

why ss stablity limit is more transient stablity limit?

0 Answers IOCL,

What is the role of the 50 STUB protection at a GIS 400KV substation with SIEMENS protection relays?

0 Answers Power Plant,

Wht ar the reason for low voltage on consumer side?

6 Answers

what is the purpose of the armored for the power Or control cable? How to select the type of the armored?

1 Answers Siemens,

what is arc flash and what are the hazards involved

0 Answers Reliance,

For more Electrical Engineering Interview Questions Click Here