Q- voltage source of 12v is driving the circuit.if circut draw the current of 0

Q- voltage source of 12v is driving the circuit.if circut
draw the current of 0.5A them source voltage will became
11.8v.what is the power dilevered by source when circuit
draw 5A current ?

Question Posted / neha singh

4 Answers
6785 Views
Ecil, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Q- voltage source of 12v is driving the circuit.if circut draw the current of 0.5A them source volt..

Answer / manu mehra

58 Watts
Explaination: while drawing 0.5A current source voltage is
11.8 volts, so internal resistance of source is 0.4ohms.
So when 5A current is drawn, internal power loss is 2 watts.
Total power generated by source is (12*5)60 watts. Hence
power delivered to the circuit is 58 watts.

Is This Answer Correct ?

0 Yes

0 No

Q- voltage source of 12v is driving the circuit.if circut draw the current of 0.5A them source volt..

Answer / badshah hussain rizvi

internal resistance is .4ohm.hence poewer loss is 10watt.so
net power delivered is 50 watts.

Is This Answer Correct ?

0 Yes

0 No

Q- voltage source of 12v is driving the circuit.if circut draw the current of 0.5A them source volt..

Answer / satya

59 watts

Is This Answer Correct ?

0 Yes

1 No

Q- voltage source of 12v is driving the circuit.if circut draw the current of 0.5A them source volt..

Answer / satya

59 watts

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Instrumentation Interview Questions

WHAT IS DIFFERENCE BETWEEN TWO WIRE RTD AND THREE WIRE RTD?

5 Answers Yokogawa,

hello i'am samad.Any one Can help me! How to calibrate Vaccum Transmitter DP Type range 0 - 50 mbar abs by hand pump calibrator.

4 Answers Bharathi Cement,

Difine flashing , Cavitaion & Noise? how to minimize these effects

3 Answers L&T,

Hi Frnds , If Suppose 1 Pair cable of 1.5 sq mm is used for Transmitter and instead of 1.5 sq mm if i used 0.5 sq mm cable will the resistance change will occur and does it affect our transmitter reading. plz mail ur answer to ntnkamble@gmail.com plz immediately mail ur reply

1 Answers

What kind of feedback is used in DP cells.

1 Answers CCIE,

can any one help me to get bel probational engineers sample question papers. I have applied for it.

0 Answers

I work on a electronic positioner transmitter 4211 at the field.I connect my multimeter in series to get the current output then I calibrate it to 4ma in 0% of position of the valve and 20ma in 100% position of the valve.My problem is in the field I get the correct output current based on my multimeter but in the dcs they only receive 40% in a output 20ma of this positioner.Then I try to simulate in this analog card and they receive the equivalent percent on the value that I simulated.Is ther any possibility to reset the zero and span of this positioner 4211 fisher.And what other possibility I can do to fixed this.This is my email add ( landicho_randy@yahoo.com )

4 Answers

Who to difference between analog in & analog out in dcs?

0 Answers

What is Positive Calibration and Negative Calibration?

0 Answers SA Kent,

we are using centum vp as monitoring with Dell precision work station T3600 but some times PC(s) are restarted automatically . how we can solve this problem? thanks

0 Answers Oil India,

What is Electrical Runout & Mechanical Runout in Vibration measurement.

1 Answers

what is the responsibility of an instrument commissioning supervisor

0 Answers Petrofac,

For more Instrumentation Interview Questions Click Here