why battery set is required for D.G.set?

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / kamesh

7 Answers
16721 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

why battery set is required for D.G.set?..

Answer / javed

It is used for starting purpose and it may also use for PLC supply.

Is This Answer Correct ?

7 Yes

0 No

why battery set is required for D.G.set?..

Answer / saahil kumar

DC is used for starting the Diesel Engine, which is used as a prime mover for the generator.

Is This Answer Correct ?

1 Yes

0 No

why battery set is required for D.G.set?..

Answer / m tahir umer

for starting purpoes of D.G set
After starting its function is over

Is This Answer Correct ?

5 Yes

6 No

why battery set is required for D.G.set?..

Answer / divya

It is used for starting purpose and it may also use for PLC supply.
It is used for starting purpose and it may also use for PLC supply.

Is This Answer Correct ?

0 Yes

1 No

why battery set is required for D.G.set?..

Answer / mukesh vaghela

we use DG set for generation of AC supply when AC supply is not available. We use DC supply of Battery for starting of DG SET only.....

Is This Answer Correct ?

0 Yes

3 No

why battery set is required for D.G.set?..

Answer / r.dharma

normally we want generate the voltage should have conistant
poles so that reson we have to give excitation i.e d.c
supply to the generator.

Is This Answer Correct ?

5 Yes

11 No

why battery set is required for D.G.set?..

Answer / 3nath

it is used to generate the field flux

Is This Answer Correct ?

1 Yes

9 No

Post New Answer

More Electrical Engineering Interview Questions

As per IS why should the control be taken only from R phase, why not from B or Y phase??!!

2 Answers

I am having a 1500 KVA transformer whose secondary current is 2086A and my connected load is 1000 KVA, I am having 400 KVAR APFCR for PF improvement what ratio of CT should i install in LT EB Bus to get optimum PF improvement?

0 Answers

while conducting an experiment why we connect the armature rheostat in maximum position and field rheostat in minimum position

1 Answers

how is find out kwh step by step

0 Answers Voith,

what is the principle of the single phase energy meter? and,what is the advantages and disadvantages of single phase energy meter?

0 Answers

why it is not advisable to run low rating (19KVA) DG sets in parallel for long durations even though they are provided with droop ckts (QDC)

0 Answers

I NEED RRB APTITUDE QUESTIONS AND MODEL PAPER,PLEASE SEND MY E-MAIL joo28_eee@yahoo.co.in

0 Answers

DEAR ALL I have motors ( 10 units )each one is 90kw 380V 50 HZ 1000rpm but new local pwer is 220v 60 hz requierd rpm should be 1000 pleas what the beast solution is used frequncy converter or rewinding all motos or chang all motors thanks

6 Answers GE,

sir please send me techinical questions for junior engineer posting in bangalore railway i am diploma holder

0 Answers RRB,

how much amp MCB is required for 1/2 kva power back up?

2 Answers Havells,

why stay insulator is not used with stay wire for 11kv Lines. Whereas it is used for LT lines ?

2 Answers Essar,

while calculating the power absorbed by a resistor connected to the output of a half wave rectifier circuit should we use rms or average current? explain with reason.

1 Answers Vedanta,

For more Electrical Engineering Interview Questions Click Here