Answer / atul $onawane

while passivation oxygen is rwemoved using sulfite to avoid
further corrosion of cooling tower parts and then chloride
cycle dealkylation process (using ion exchange
process)carbonate and bicarbonates are removed. ion exchange
process treates pretreated water.(i.e softened water using
chemical such as zeolite.)

Answer / vinayak

WATER SOFTNER

Answer / sundar

simple word minimize the chemical reaction in cooling tower

NATURAL GAS ENGINEERING - QUESTION 26.1 : (a) In natural gas pipe sizing, the length of the pipe from the gas source metre to the farthest appliances is 60 feet. The maximum capacities for typical metallic pipes of 60 feet in length are : 66 cubic feet per hour for pipe size of 0.5 inches; 138 cubic feet per hour for pipe size of 0.75 inches; 260 cubic feet per hour for pipe size of 1 inch. By using the longest run method : (i) Find the best pipe size needed for the capacity of 75 cubic feet per hour. (ii) Estimate the suitable range of capacities for the pipe size of 1 inch. (b) The maximum capacities for typical metallic pipes of 50 feet in length are : 73 cubic feet per hour for pipe size of 0.5 inches; 151 cubic feet per hour for pipe size of 0.75 inches; 285 cubic feet per hour for pipe size of 1 inch. By using the branch method find the best pipe size needed for the capacity of 75 cubic feet per hour when the length of the pipe from the gas source metre to the appliance is 52 feet.

2 Answers  

---

BIOCHEMICAL ENGINEERING INSTRUMENTATION - EXAMPLE 29.6 : In infrared spectrum, one of the factors affecting peak location is the mass of the atoms. The stretching frequency of a bond connected to a lighter atom will be greater than the same bond connected to a heavier atom. (a) For halogens like florine (F), chlorine (Cl), bromine (Br), iodine (I) and astatine (At), what is their IUPAC group number? Hint : The proton numbers for F, Cl, Br, I and At are 9, 17, 35, 53 and 85 respectively. (b) For the compounds of H-F, H-Cl, H-Br, H-I and H-At, which one has the lowest stretching frequency and which one has the highest stretching frequency? State the reasons.

1 Answers  

---

Question 78 - Fact 1 : Dry air contains 20.95 % oxygen, 78.09 % nitrogen, 0.93 % argon, 0.039% carbon dioxide, and small amounts of other gases by volume. Fact 2 : Volume occupied is directly proportional to the number of moles for ideal gases at constant temperature and pressure. Fact 3 : 12.5 moles of pure oxygen is required to completely burn 1 mole of pure octane. Fact 4 : Air–fuel ratio (AFR) is the mass ratio of dry air to fuel present in a combustion process such as in an internal combustion engine or industrial furnace. Fact 5 : Molecular weight of oxygen gas is 31.998 g / mole and molecular weight of nitrogen gas is 28.014 g / mole. (a) Find the molar ratio of nitrogen and oxygen, or (moles of nitrogen) / (moles of oxygen) in dry air, by assuming ideal features of nitrogen and oxygen gases. (b) How many moles of nitrogen are available if dry air is used to completely burn the 1 mole pure octane? (c) Find the mass of fuel of 1 mole of octane with molecular weight of 114.232 g / mole. (d) Find the mass of dry air with 12.5 moles of pure oxygen by assuming only oxygen and nitrogen gases exist in the air. (e) Find the air-fuel ratio (AFR) when octane is used as fuel. (f) Find the fuel-air ratio (FAR) when octane is used as fuel.

1 Answers  

---

Question 84 - In Mendelian genetics, yellow (Y) is dominant to green (y) and round (R) is dominant to wrinkled (r). (a) What is the probability P of Rr x Rr producing wrinkled seeds? (b) What is the probability P of Yy x yy producing green seeds? (c) What is the probability that RRYy x RrYy would produce RrYy?

1 Answers  

---

Heat transfer: In a triple effect evaporator, the heat transfer for an evaporator is calculated as q = UA (TI - TF) where TI is the initial temperature, TF is the final temperature; U and A are constants. Given that heat transfer for the first evaporator : q(1) = UA (TI - TB); second evaporator : q(2) = UA (TB - TC); third evaporator : q(3) = UA (TC - TF) where q(x) is the heat transfer function, TB is the temperature of second inlet and TC is the temperature of third inlet, prove that the overall heat transfer Q = q(1) q(2) q(3) = UA (TI - TF).

1 Answers  

---

QUANTUM COMPUTING - EXAMPLE 32.1 : In quantum computing, let the amplitude A = a | 0 > + b | 1 >, | a | | a | + | b | | b | = 1. Find the values of b if A = 0.8 | 0 > + b | 1 >.

1 Answers  

---

How can hexavalent chromium be removed from aqueous waste streams?

0 Answers  

---

What is % of piping & equipment cost for a chemical plant having batch process?

0 Answers  

---

ENGINEERING DRAWING - EXAMPLE 18.1 : For a Vernier scale of representative fraction (RF) = 1 / 25, calculate the length of the scale for the reading up to 4 metres.

1 Answers  

---

When an expansion is joint needed on the shell side of a shell and tube heat exchanger?

0 Answers  

---

Question 83 - The United States of America Energy Information Administration reports the following emissions in million metric tons of carbon dioxide in the world for year 2012 : Natural gas : 6799, petroleum : 11695, coal : 13787. Coal-fired electric power generation emits around 2000 pounds of carbon dioxide for every megawatt hour generated, which is almost double the carbon dioxide released by a natural gas-fired electric plant per megawatt hour generated. If 1 metric ton = 1000 kg and 1 pound = 0.4536 kg, estimate the total energy generated by natural gas in the world for year 2012, in gigawatt hour.

1 Answers  

---

ENGINEERING NUMERICAL METHODS - EXAMPLE 19.1 : Solve the simultaneous equation using simple Excel program : r + s - t = 7, 2r - s = 0, 3r + 2t = 15. Explain the use of functions of MINVERSE and MMULT together with the keyboard C (Ctrl) + S (Shift) + E (Enter).

1 Answers  

---