Explain the difference between cfm (cubic feet per minute) and scfm (standard cubic feet per minute)?

0 Answers  

---

The water is superheated steam at 440 degree Celsius and 17.32 megapascals. Estimate the enthalpy of the steam above. From the steam table for water at 440 degree Celsius, enthalpy of steam, h at 18 megapascals is 3103.7 kilojoules per kilogram and at 16 megapascal is 3062.8 kilojoules per kilogram. Assume that h = mP c where P is pressure; m and c are constants at fixed temperature with small differences in P.

1 Answers  

---

What is control valve ?

2 Answers   TCL,

---

what is factories act?tell about factories act?

1 Answers  

---

QUANTUM CHEMISTRY AND CHEMICAL ENGINEERING - EXAMPLE 31.6 : In N + 1 Rule in Quantum Chemistry, whenever a spin 1 / 2 nucleus is adjacent to N other nuclei, it is split into N + 1 distinct peaks. In 1 peak or singlet, there is only 1 magnitude. In 2 peaks or doublet, the ratio of magnitude of each peak is 1 : 1. In 3 peaks or triplet, the ratio of magnitude of each peak is 1 : 2 : 1. In 4 peaks or quartet, the ratio of magnitude of each peak is 1 : 3 : 3 : 1. In 5 peaks or quintet, the ratio of magnitude of each peak is 1 : 4 : 6 : 4 : 1. (a) By using binomial coefficients or Triangle of Pascal find the ratio of magnitude of each peak if 6 peaks exists. (b) How many adjacent nuclei are available in a spin 1 / 2 nucleus in such situation of 6 peaks?

1 Answers  

---

PROCESS DESIGN - EXAMPLE 21.1 : According to rules of thumb in chemical process design, consider the use of an expander for reducing the pressure of a gas when more than 20 horsepowers can be recovered. The theoretical adiabatic horsepower (THp) for expanding a gas could be estimated from the equation : THp = Q [ Ti / (8130a) ] [ 1 - (Po / Pi) ^ a ] where 3 ^ 3 is 3 power 3 or 27, Q is volumetric flowrate in standard cubic feet per minute, Ti is inlet temperature in degree Rankine, a = (k - 1) / k where k = Cp / Cv, Po and Pi are reference and systemic pressures respectively. (a) Assume Cp / Cv = 1.4, Po = 14.7 psia, (temperature in degree Rankine) = [ (temperature in degree Celsius) + 273.15 ] (9 / 5), nitrogen gas at Pi = 90 psia and 25 degree Celsius flowing at Q = 230 standard cubic feet per minute is to be vented to the atmosphere. According to rules of thumb, should an expander or a valve be used? (b) Find the outlet temperature To by using the equation To = Ti (Po / Pi) ^ a.

1 Answers  

---

HEAT TRANSFER - EXAMPLE 5.3 : In a cylinder with a hollow, let a is outside radius and b is the inside radius. In a steady state temperature distribution with no heat generation, the differential equation is (d / dr) (r dT / dr) = 0 where r is for radius and T is for temperature. (a) Integrate the heat equation above into T(r) in term of r. (b) At r = a, T = c; at r = b, T = d. Find the heat equation of T(r) in term of r, a, b, c, d.

1 Answers  

---

ELECTRICAL TECHNOLOGY - EXAMPLE 16.2 : In a selection of suitable heating equipment for drying of crystals of biochemical, the one of the lowest current consumption will be chosen for safety consideration. Selection is available : (A) 120 V microwave oven 1800 W. (B) 240 V conventional oven 11000 W. Which one should be chosen and why?

1 Answers  

---

what is the role of id fan in a furnace?

3 Answers   Essar, JSW,

---

Explain the functioning of a three-way catalytic converter.

0 Answers  

---

how can we calculate reflux ratio? what is difference between internal reflux and external reflux?

0 Answers   Sabic,

---

What industries require filtered compressed air?

0 Answers  

---