Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


Explain Difference between Bech set and operating range of
control valve

Answers were Sorted based on User's Feedback



Explain Difference between Bech set and operating range of control valve..

Answer / rakesh kumar.n be

if u do the adjustment in the string at the actuator, or
compress the spring, u will get the opposing force to move the
stem in the control valve that is called bech set .it depents
on the control valve. mostly foe small valve we use 3-15 psi
and for medium we use 6-30 psi .thanks

Is This Answer Correct ?    3 Yes 0 No

Explain Difference between Bech set and operating range of control valve..

Answer / rakesh kumar.n be

if u do the adjustment in the string at the actuator, or
compress the spring, u will get the opposing force to move the
stem in the control valve that is called bech set .it depents
on the control valve. mostly foe small valve we use 3-15 psi
and for medium we use 6-30 psi .thanks

Is This Answer Correct ?    0 Yes 0 No

Explain Difference between Bech set and operating range of control valve..

Answer / ilayaraja

both r same.bench set is called inherent pressure range of the actuator.that is maximum and minimum pressure applied to the actuator.

Is This Answer Correct ?    0 Yes 1 No

Post New Answer



More Instrumentation Interview Questions

what is difference between Floating D.C.Voltage and Fixed D.C.Voltage?

2 Answers  


Please explain the difference between instrument range and calibration range in terms of pressure transmitter? line design pressure: 93 bar operating pressure : 82 bar press Transmitter Range? calibration range ?

3 Answers   L&T,


hw to calibration a control valve?

3 Answers  


How much should be the values and/or percentages of these given below factors for a good controller ? Steady state error Delay Rise Time Overshoot Peak Time Settling Time Damping Oscillations & vibrations thanks

1 Answers  


Close loop and open loop.

3 Answers   CCIE,






how can we tune a PID. If it is by zeiger nichols method..please explain briefly with help of an example.

0 Answers   KNPC,


what is the essential difference between DIODE and SCR in term of application.

2 Answers   ADMA OPCO,


My question may be very basic or childish but this question still persists in me, someone plz help me 1.why do we go for differential equations to analyze a system? 2.why do we solve it using matrices, is there any specific reason for using matrices other than the stories like it is simple,faster etc.

2 Answers  


How to find out the current of two motors having same power consumption but different RPM?

0 Answers  


i am preparing for BARC ,so plz mail me how to prepare for BARC. ALSO IF POSIBLE SOME RELATED QUESTIONS. MY MAIL ID IS khushi_4uall2003@yahoo.co.in

0 Answers  


IS there any effect of vortex in low pressure side of the transmiter after the orific in feed water line? if yes then what is the calculation?

0 Answers  


how can i calibrate the temperatuture gauge used by temperature bath(dry block) i mean step by step procedure?

0 Answers   Texas,






Categories
  • Civil Engineering Interview Questions Civil Engineering (5074)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4444)
  • Electrical Engineering Interview Questions Electrical Engineering (16594)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2986)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (123)
  • Power Plant Engineering Interview Questions Power Plant Engineering (170)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1377)