Interested to Buy Any Domain ? << Click Here >> for more details...
What is Lap Length??????
- 24 Answers
- 73163 Views
- CCCL, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / venu gopal
It is used in construction when you are working with
reinforcement steel. when you are at the end of any bar and
it has to be further extended to some more distence then
you are supposed to join it with an other bar (what ever
may be the dia) to this job simply we cannot do it. there
is a design and it depends on the location and design. in
most of the cases it is 50 times the diameter of the bar
which you are laping in some cases it may be 40times the
dia and in some drawings base on the requirementt and
design it will be a standardlength (300mm,400mm soon....)
| Is This Answer Correct ? | 128 Yes | 13 No |
Answer / maheswaran
IN COMPRESSION MEMBER 46D
IN TENSION MEMBER 50D
| Is This Answer Correct ? | 63 Yes | 8 No |
Answer / aju kavanattu
Lap length is joining of two bars,this length is depends
upon desgin (some times 50 times of bar).
| Is This Answer Correct ? | 19 Yes | 2 No |
Answer / mohammed nadeem
the length of lap joint from joggle joint(where bar is
usually bend for lap) to end of bar is 48 times of diameter
of bar.but due to arises of problems in field is can be
taken as 50 times of diameter of bar.
| Is This Answer Correct ? | 12 Yes | 3 No |
Answer / mohammad abdullah
Its depends upon the design and Load, mostly in field following overlaps are use
48*D
or
50*D
| Is This Answer Correct ? | 12 Yes | 5 No |
Answer / shahnawaz
We use Lap in construction work with TMT bars mostly we use
50xd,40xd etc. but we can not decide infect its totally
depend on Design of the building.
| Is This Answer Correct ? | 7 Yes | 2 No |
Answer / neeraj chauhan
lap length also depands upon grade of concrete and its genraly use 50 d
| Is This Answer Correct ? | 9 Yes | 5 No |
Answer / vidyasagar daley
It is not fixed value it is depending on the grade of concrete because of the bond strength different for different grade of concrete
| Is This Answer Correct ? | 5 Yes | 2 No |
Answer / benarji
generally now at Commercial building using
every were r using 50*dia of the bar
some times compression side 45 *dai ofthe bar are used
| Is This Answer Correct ? | 13 Yes | 12 No |
what is the design procedure for building
how to absorb to site basic corrections? which are the important correction?
Explain what is the difference between built area and super built up area?
How much snowcem required per sq. Meter area
3 Answers Bhushan Power Steel,
SAND AND STONE AGGREGATES WASTAGE PERCENTAGE IN CONCRETING WORK?
how to calculate length of bar
after temping in cbr mould keep how many hours mould in water
what is BOQ? BOQ IS US IN ESTIMATE
hello; sir. i would like to be an assistant executive engineer in irrigation department. is it really necessary to take coaching? or can i prepare myself by studying any study materials available in market? if so; what are the books i have to purchase. please reply soon.
What is the Allowable silt content of sand for construction purposes?
What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?
how to calculate the steel quantity for columns and beams
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
