HELLO FRIENDS plz tell me which are the PROTOCOLS we are
using in PLC

Answers were Sorted based on User's Feedback



HELLO FRIENDS plz tell me which are the PROTOCOLS we are using in PLC..

Answer / ashish khatana

Protocol Transport

Ethernet/IP TCP/IP
AB/CSPv4 TCP/IP
Modbus/RTU UDP/IP
DF1 Radio Modem UDP/IP

Is This Answer Correct ?    7 Yes 0 No

HELLO FRIENDS plz tell me which are the PROTOCOLS we are using in PLC..

Answer / lalith kumar

RS485
RS232
Ethernet TCP/IP
Profibus
Modbus

Is This Answer Correct ?    3 Yes 0 No

HELLO FRIENDS plz tell me which are the PROTOCOLS we are using in PLC..

Answer / rahul dev

DIfferent types of protocol is used in PLC .

1. Modbus RTU/ASCII
2. Unitelway
3. TCP/IP
4. Modnet(Modbus TCP/IP)
5. Devicenet
6. Can Open
7. Profibus
8. Modbus Plus
9. DH+
10.Arcnet
there are more protocols these are used according to your
requerment.

Is This Answer Correct ?    2 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

can you send remote seal interface level transmitter calculation steps for oil water saperator.

0 Answers   Sasol Firm, Thermax,


My question may be very basic or childish but this question still persists in me, someone plz help me 1.why do we go for differential equations to analyze a system? 2.why do we solve it using matrices, is there any specific reason for using matrices other than the stories like it is simple,faster etc.

2 Answers  


How d.p. Transmitter can be applied to close tank?

0 Answers  


1 bar is equal to how many pound per square inch(psi)?

14 Answers   Essar,


Q- Control problem are mainly classified in _____ types. a-)4 b-)3 c-)6 d-)nono of these Few of them i know is 1- regulator type problem (eg- Air conditioner) 2- tracking problem (eg missile trcking problem) 3- sybernatics 4- optimal control problem

0 Answers   Sail,






how can calibrate transmitter online

2 Answers  


What is the PLC Level & type.

2 Answers   Bhushan Power Steel,


Reasons for using seal pots:

1 Answers  


Draw a complete P&ID of a flow suction tank indicating all control & protection equipment. Indicate all its inlets and outlets. Explain the controls for this system

0 Answers  


Exapain Deatails of the PID controlller

4 Answers  


what is difference between RTD , thermo couple and thermistor in general ?? (except temperature co-efficient )

5 Answers   Bilt,


Can anybody explain what is the different between ESD & PLC

1 Answers   ADCO,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)