Answer / rk

UPSs are sued not just in software companies, but in many
other firms, where continuity of electric power is critical
for operations. UPS (Uninterruptable Power Supply), is an
device that works on batteries with associated electric
circuitry to ensure the power supply is uninterrupted in
the event of primary electric power supply is disrupted for
some reason. Since, power outages are common in India, the
usage of UPS or inverter (mostly found in Indian homes)is
quite common in india to ensure uninterrupted power supply.
However, the capacity of UPS is specified in number of
hours it can provide certain rated power.

Answer / ramendra shukla

The UPS is a device which provide us the continuous power
without any breaking in normal supply.Due to requirement of
continuous supply for critical load UPSes are get used in
IT companies as well as for Non IT companies.
Untruptted Power Supply (UPS )-have mainly five parts-
Rectifier,Battery Bank,Inverter,Switching & controlling
devices.Their working is based on logic controll.
At the presence of normal electric supply the load flows
from Rectifier-Inverter-Switch but when AC supply in not
presented at all then Battery units come into picture.By
the working principal or inverter i.e. from DC -AC it
feeded AC supply to the load after Ac filterisation.
When there are any problem in Rectifier ,inverter, Battery
etc. unit then supply goes through bypass.
Isolating transformer is a type of X-mer which isolate the
a circuit to its design.and also the No. of primary
&Secondary tern of Iso. X-mer are same are equal that
facilitates to isolates and reduce the fluctuation and also
create Neutral supply for load.

Answer / anoop

isolation transformer is having same no. of turns in
primary and secondary side as rightly said by one of our
friends. its main purpose is used to isolate/remove the dc
components from ac, as transformer cannot transform dc from
one circuit to another because there will not be any rate
of change of flux associated with dc. so sewcondary side
Kva will be dc component free.

Answer / salim

In this case isolation t/f is used for reducing hormonics and provide isolated nutral to load

Answer / vipul mali

Isolation transformer is a kind transformer which isolates
the two voltage levels . and provides pfotection towards
low voltage side. it is used in the electronic kits.

IN A HT CABLES i.e. 1.9/3/3 kv, what is the meaning of 1.9 and 3.3.

1 Answers  

What is diffrence bitween electrical and electronics ?

4 Answers  

We've 2 diffrent DG's with same capacity (500 KVA). Can we sync them ?

1 Answers  

explain Uninterrupted power supply detailed electronical operation with circuit diagram

1 Answers   Emerson,

i need to give section engineer (electrical engineer) for RRB. Please suggest some book

0 Answers  

At 765Kv, I have seen the use of PT at line side for metering and CVT for protection, although as far as my knowledge is concern, PT at this voltage level will have huge loss and more cost as compared to CVT as CVT can also perform same function of Protection and Metering? So my question is why use PT and not CVT for metering and protection in order to reduce the cost.

1 Answers  

typically in power distribution substation. 1- Any idea how would be the graph of capacitor bank consumption verses time through the day . 2- How is the switching ( on and off ) of the capacitor bank, per need?

0 Answers   Siemens,

when we megger is not damaged when we are measuring very low resistance? high d.c. voltage is produced in megger so according to i=V/R. current will be high so what is the reason ?

1 Answers  

How can we do megger test of cable??

2 Answers  

why rating of motor in HP

2 Answers   MSL,

What is meant by operating sequence of VCB : 0–0.3sec.–CO– 3min.-CO

2 Answers  

How to run 1ph motor(230 VOLTS its full load amps is 4.5 ampa))with 480 volts main(we didn hav neutral)Thn we go for step down transformer.Our load 10 amps,so we conisder this amps in primary are secondary side?

1 Answers