What is C check in a diesel generator and what are parts and what has to be do

What is C check in a diesel generator and what are parts
and what has to be done during the C check

Question Posted / kudipudibhanuprakash

4 Answers
17253 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What is C check in a diesel generator and what are parts and what has to be done during the C chec..

Answer / shri..

Major thing in c check is that gap in between inlet valves
& rocker has been check & maintain, the end clearance of
crank shaft has been check & maintain. + B check also
carried out in c check.

Is This Answer Correct ?

24 Yes

7 No

What is C check in a diesel generator and what are parts and what has to be done during the C chec..

Answer / sathish n p

C check is carried out along with A & B ,

B checks
Coolant level
Oil filter replacement.
Fuel filetr replacement.
Alernator terminals tightness checking.
Replacement of lubricating oil....etc

C checks.
Coolant level replacement.
Check the fuel injectors etc..

Its depends on the size of the DG sets , auxillary
system,freuency of mainttenance ...

Is This Answer Correct ?

18 Yes

2 No

What is C check in a diesel generator and what are parts and what has to be done during the C chec..

Answer / yuvaraj

Taper shaft in a crank has to check, cylindrical block
surface to check and + B check also carried out in c check

Is This Answer Correct ?

12 Yes

2 No

What is C check in a diesel generator and what are parts and what has to be done during the C chec..

Answer / sanath shetty

C-Check is done in (Every 800-1500 Hrs.)
following are the checks
1. Change oil.
2. Change oil filter,fuel filter,bypass filter.
3. Change Air Filter.
4. Change water Separator
5. Radiator cleaning with chamical
6. Check All Electrical terminal & thimbles
7. Check polution level.

Is This Answer Correct ?

9 Yes

2 No

Post New Answer

More Electrical Engineering Interview Questions

What are the advantages and disadvantages of the dc motors?

0 Answers

How many wall/floor flange will i use in bus duct system if we have in our design a 35th floor building.

0 Answers

what is the effect if we add capacitor on DG supply, it has any loss or benefit.

6 Answers

why in large rating C.T.s equipotential wires are used?

2 Answers Essar,

At what point crngo works like as crgo

0 Answers

Explain what is CBCT.

1 Answers

(1) From the following option, which option is correct for largest size transformer.? a)1KVA,25Hz , b)1KVA,50HZ , c)1KVA,60Hz , d)1KVA,100Hz

5 Answers Torrent Power,

we have a 2000kva step down transformer at our site. The HT side is charged from 22000V. So the primary current will be 52.48A. So why the HT breaker(SF6 ABB) is rated of 1250Amps ?

2 Answers

how to test a motor from megger

5 Answers JSW,

WE HAVE A LOAD OF 55KW MOTOR ITS VOLTS 380 3PH AND ITS TAKING 100AMPS (ITS FULL LOAD IS 105AMPS)AND ITS CABLE IS 4CX50SQMM ,NOW ITS GETTING ABNORMAL HEATUP IN CABLE,PLZ TELL WHY ITS HEAT-UP?(CABLE LENGTH IS 15 METERS ONLY)

10 Answers

What is the meaning of 40X8X2 busbar dimensions for carring load of 400 Amps

0 Answers

pls,send the previous year written test questions.

0 Answers

For more Electrical Engineering Interview Questions Click Here