Answer / murali

Try to get the MODBUS communication details,address &
parameters which are all can able to read from the ER300P
meter from your supplier or direct from L&T.
With those inputs we can do anything

Answer / pearl george

there are so many softwares available on the net such as modscan, simplymodbus by which u can communicate. rs485 port uses the modbus rtu mode of communication in L&T er300p.with these softwares u can get the values like voltages, current, pf, frequency etc that are stored in the holding register of the meter. to communicate with the energy meter u hav to prepare a query with the required function code.
more details required, pls feel free to ask me

Answer / pearl george

hey anis..
i wud b happy to help you.. but i jus remembered dat power consumption s nt available at d holdinding regisers of the meter. in my projct, i had to only acquire d pawer which i calculatd from the V, I n power factor dat will be updated in d register n d query i talked abt is used to write to dose registers.. so.. i dunno if my query wud help you..
y dnt u access d data to d pc n dn develop a software werin u can do d calculations recquired? i can try helping if dats d case.. coz v used vb.net to develop a software wer v tuk dese voltage n all n den calculated der..

Answer / anbh

Hey I have more questions on ER300P. Can I have ur mail id
plz. Thanks. ANBH

Answer / pearl

wat is dat u wanna knw? i comleted dat projct.. if u want ny help, mail me..

Answer / ab

I'm using this meter to study the power utilization for
several load settings in a complex theromchemical
plant.....At the begning of every measurment I want to
round off the start point of the power consumption reading
to 4 digits (ex:xxxx0000)....so that I can apply my algo on
the readings which I get at the end of my measurement.

Does any one of you know how to do it?

Answer / pearl george

u can write in the meter using write code using modbus. jus chek the location of the power using modscan or sum silmple software n then u can write in dat location with a loop or sumtng at ur will..

Answer / anbh

Thank you very much George.
As I know from ER300P manual....we have a programing
password with which I can change some settings of the meter
like CT\PT ratio and RTC etc...So can I use the same
programing password to write to the location of current
power consumption?

Thank you again.

With best regards,
Anis

Answer / anbh

Hello George,

It's again me(Anis)....
In ur 1st reply you wrote..."to communicate with the energy
meter u hav to prepare a query with the required function
code"....Can you plz share the query you worte for your
project and also plz let me know where can I find the
function code to write to the address of total power
consumption.

Regards,
Anis.

Answer / siva kumar

Hi george, i am siva, i have L&T Trivector Meter ER300p, Can
u guide me how to take data from the meter

Why is a dead weight tester so called by that name?

1 Answers   SGS,

in DCS or PLC we can not put all ai or di,there is calculation through which we can accomodate certain no of digital and analog signal.I need to know that calculation

1 Answers  

why we are using pnp npn for sensors is there any other type?

1 Answers   CGL,

What should we do when Fisher Fieldvue DVC2000 give some out put air at 4mA bt at that i need no out put

1 Answers  

how pressure transmitter work, what is its principal to measure and how its generate signal. for pressure transmitterinstallation which precautions must be taken ??

0 Answers  

loop chech tools list

1 Answers   BAP,

what is the diffrence between mmwc and kg/cm2 for pressure measurment when we are using mmwc and when kg/cm2 and why????? ?? what is the reason

19 Answers   Ecoboard, Jindal, Sepco,

what is differance  between SOE an alarams

1 Answers   BMM,

what is the function of a zener diode ?

2 Answers   Honeywell,

how to calibate level transmiter ?range -150 to +150.what is the zero and span?

1 Answers  

how the transmitter send MA?

1 Answers  

We do have a problem in the company that is one PT connected to PlC which is mean 1 out of 1 in PLC system we do have the PAHH is 55 mbar and PALL 8 mbar with a timer of 15 sec for the PAHH the problem started when PAHH goes more than the set point which is 55 it reached up to 71 but due to timer doesn't trip . We force it and we checked everything nothing there . We replaced the transmitter problem still there the reading goes more than the 55 bar the range for transmitte is 0- 60 mbar . So we did loop check , aculaizing valve , wiring all are okay . What the possible causes for this ???

2 Answers   National Petrochemical Company,