Answer / mail2noor.hyd

when we r measuring very low pressure :: mmWC
and measuring high pr. :: kg/cm2/bar/psi... ok
for example we r measuring like boiler furnaces
pressure(draft) i.e very low pr.(250mmWC) so we r measuring
in mmWC, and when we r calibrating the transmitters (flow
and level) that time also we r calling transmitters range
also mmWC ok

here note the point is 10,000 mmWC = 1 Kg/cm2 then
1mmwc=0.0001kg/cm2 ok

Answer / vaibhav v t

10000 mmwc equals to 1 kg/cm2.
For low ranges pressure is mentioned in MMWC otherwise in
any other pressure units.

Answer / dhirendra

Mostly both are units of pressure. when we measure the very
low pressure than it is expressed in mmwc else higher
pressures are measured in kg/cm2. low pressure can also be
used for but the error in values will be more.
Basically 10000 mmwc is 1 kg/cm2 a.

Answer / dilip

N/m2 is SI Unit and Kg(f)/cm2 is MKS Unit.

1 Kg/cm2 is 1.033 bar or 1.033x10^5 N/m2
10000 mmwc= 1 kg/cm2

Answer / tapan das

Mostly both are units of pressure. when we measure the very
low pressure than it is expressed in mmwc else higher
pressures are measured in kg/cm2. low pressure can also be
used for but the error in values will be more.
Basically 10000 mmwc is 1 kg/cm2 a.

Answer / m.vijay kumar

both r units for pressure,.but,mmwc(millimeter water column)is
very low pressure means less than zero.here, 10000mmwc=1kg/cm2.we may consider the mmwc as vaccum.

Answer / prashant meena

Mostly both are units of pressure. when we measure the very
low pressure than it is expressed in mmwc else higher
pressures are measured in kg/cm2. low pressure can also be
used for but the error in values will be more.
Basically 10000 mmwc is 1 kg/cm2 a.In thermal power plant mmwc is most useful in boiler side.

Answer / rajeev tyagii

MMWC (MILIMETR WATER COLOUM)IS A LOW PRESSURE MEASURING UNIT USE FOR LOW MEASURING AS GAS FLOW ETC AND ONE KG =10,000 MMWC.
MOSTLY USE IT INTO SAMPLE FLOW OF GASES IN ANALYSER AND FLOWMETER AND PREESURE SETTING of pressure switch also.

Answer / chirag darji

both r units of pressure itself..but when the system is in
vacuum then the pressure measured in mmwc and the positive
pressure measured by kg/cm2.so for low pressure mmwc used
and for high pressure kg/cm2 is used..

Answer / md tasleem khan

To measure low pressure we need to use this unit of
pressure Hence 10000mmwc=1kg/cm2

plz you help about Que paper of mahagenco previous your,any model paper relad to it{maharastra power genration}

0 Answers   MahaGenco,

what is cascade controller ?

6 Answers  

how many types of spped sensors n vibration sensors?their basic principle n connection?

0 Answers   IOCL, ITC Infotech,

Why integral control mode call Reset controller?

1 Answers  

What is the difference between a PLC (Programmable logic controller) and DCS (distributed control system)?

7 Answers  

Basic working principle of control valves

1 Answers  

What is the relation between electronics & instrumentation

2 Answers  

What is fault tolerent system

2 Answers   GNFC,

What should be the stanchan Height for installation of Smoke detector & toxic gas detector in field,according to qatar standard

2 Answers  

Can anyone send most commonley asked Instrumentation questions and answers in cement industry please?

0 Answers  

Can Any body tell me how to check Modbus Settings in ER300N L&T trivector meter?

0 Answers  

what is the meaing of calibration curve?

3 Answers   HCL, Honeywell,