Answer / lbbs

It seems most answers are ommiting the essential
function/characteristic(ON LOAD).I have a vague idea may be
someone will add.
It is my understating that with this tap changer you can
change winding tap position without breaking/swithing off
the load.This is achieved by the MAKE BEFORE BREAK
mechanism in the tap switch.
Hope someone will add.

Answer / kamlesh

low loss transformer with OLTC how many % losses?

Answer / pinaki chatterjee

O.L.T.C IS NOTHING BUT A SWITCH WHICH CAN BE OPERATE DURING THE TRANSFORMER IS RUNNING AT ANY LOAD WITH OUT ANY PROBLEM.IT FACILITATE THE OUT WILL BE FIXED WHETHER THE INPUT IS VARIABLE

Answer / sreejith

3 is correct

Answer / shanmuganathan

on load tap changer.only used for voltage level increasing
or decreasing in secondary side for transformer side.for
exp:customer need 430v transformer primery side 11kv

Answer / raj lahare

Dear Dnyaneshwar, Please mote that 1)In HV transformers the LV winding is nearer to core and the HV winding is away from Core There fore it is easy for taking the taps .2) The current in HV being lower the switching current in OLTC is low.
Please note. 3)The RTCC means the Remote Tap Change Control Cubical This is installed in Control Room so that the Taps of the Transformer which is installed in Switch Yard can be changed from the Control room only. 4)The RTCC if provided with AVRCR then the taps are changed automatically by sensing the LV voltage. The AVRCR means AUTOMATIC VOLTAGE CORRECTION RELAY. 5) In bigger transformers say Voltage class 220 KV and above the OLTC tap connections are provided on LV side due to the insulation levels of high voltages at the switch.

Answer / savi

OLTC is using for cntrolling transformer output voltage

Answer / puneet

ALL ANS. ARE CORRECT, BUT I WAN TO KNOW THAT WHERE IN THE DISTRIBUTION SYSTEM STEP-UP TRANSFORMER R USED! SO THE OUTPUT SIDE IS NOT HV BUT LV..

Answer / srikanth

OLTC is nothing but Voltage Regulator, as the function of
voltage regulator is to give constant output irrespective of
the input voltage fluctuations.



OVER LOAD TAP CHANGER

Answer / manoj kumar

oltc is on load tap changer. it is typical winding
connecton for a resistor type high speed oltc provided at
the neutral end of eaach phase of windings of a star
connected 3-phase transformer.

there are 3 transformers each of 1500 kva and one transformer of 1000kva for a 11 floor building . total otgoing kw is 4066 kw. i need an extra 260 kw .is there any provision for that? what is the max kw that can be connected with these transformers?

2 Answers  

how is working the auto transformer?

1 Answers  

What is the meaning of burden and class of accuracy of CT?

1 Answers   Home,

Explain the role of a car driver as one of a feedback mechanism.

0 Answers   GE,

where rlc series ckt used?

0 Answers   ABB,

What is the operating range of voltage and current in grid supply in India?

4 Answers   BARC,

what are all the components required to assemble solar panel other than pv cell?

0 Answers  

what is the difference between gas group b and gas group c electrical equipment construction wise?

0 Answers  

two parallel conductors are carrying the current in the same direction.which of the following statements is true? (a)there is arepelling force between the conductors (b)the force increases when the distance between the conductors is increased (c)there is an attaracting force between the conductors (d)the force increases when the distance between the conductors is decreased

1 Answers  

In MEP Services what are parts of STP and what are there function?

0 Answers   Tenon,

why does not tester light up when it is touched to neutral of 3 pin socket.

4 Answers  

Hello sir This is prakash from bangalore i have a doubt why we have to maintain DG power factor in the range 0.78 to 0.8 Perhaps i f it is increased means what will happen in DG

3 Answers