how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER havi

Categories >> Engineering >> Electrical Engineering
Suggest New Category

how much loading in terms of ampere can put on 5 MVA,33/11
KV TRANSFORMER having rated current 263 Amp ?????????

Question Posted / guest

11 Answers
37704 Views
ABB, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / sunil bhuarya

its sunil bhuarya
ans of this question is ut self in the que.
how-
5000/(root3)*11=262.43 aproxx=263
and in case of overloading it becomes 300 to 315A.

Is This Answer Correct ?

38 Yes

7 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / ynrao

263 Amps as the question itself says

Is This Answer Correct ?

29 Yes

7 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / serwox

Answer depends on what percentage overload a transformer can
accept. For a tx that can accept a 120% overload, the
current is 315A.

Is This Answer Correct ?

20 Yes

5 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / pravin

Actually it depends upon designer. If we asked designer to
designed for 125% overload, he will provide cooling per
current loading on 125% overload to restrict Hot Spot Temp.
of the winding & Top oil temp. respective to max. ambient
temp.
In this case, we can provide loading of 437A in
terms of ampere on top rating with Hot spot temp & top oil
temp in control on top rating. Actually transformer has
three rating OA/FA/FA. If this transformer is OA/FA/FA then
we can provide this loading.
If it is self cooled then 263A is max. loading.

Is This Answer Correct ?

5 Yes

1 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / sunil kumar das

above answer is also correct.we can put less than full
load current.

Is This Answer Correct ?

6 Yes

3 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / jayant subhash golait

If the word rated current comes,then it is actually safe n maximum permissible limit....Obviously,the machine will misbehave when crossed this limit...to save the machine or to avoid failures,extra cooling may be required that is also within tolerable range...again the manufacturer may declare that value as a rated current which is itself little bit away from tripping or breakdown or danger zone of tolerance....finally ,it is solely depend upon manufacturer n in turn the quality of raw material used to design the machine....

Is This Answer Correct ?

1 Yes

0 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / narayanan surendran

The question did not talk about cooling and Tap Changer Type.
If over loaded, voltage drop and over heating may occur.
Therefore given rated current 263 A is correct.

Is This Answer Correct ?

0 Yes

0 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / sam

That depends on the rated output's power factor and the
load power factor.

Is This Answer Correct ?

2 Yes

3 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / har

300amp

Is This Answer Correct ?

8 Yes

10 No

how much loading in terms of ampere can put on 5 MVA,33/11 KV TRANSFORMER having rated current 263..

Answer / pankaj

Normayy transformer gives max efficieny at 75% of its rated
capacity because in that case cu loss = iron loss.

Is This Answer Correct ?

1 Yes

9 No

Post New Answer

More Electrical Engineering Interview Questions

WHY SPEAKER OUTPUT IN WATTS??

2 Answers

what is the difference between earth and neutral?

56 Answers Bhel, Emerson, HCL, JLL, L&T, Siemens, TVS,

The power dissipated by a resistor of 10ohm when a current of 2A passes through it is:(a) 0.4W(b) 20W(c) 40W(d) 200W

2 Answers

1.Why we use choke?If we use for high starting voltage then different type choke gives different voltage. Is it correct?

2 Answers Dalkia, Luminous,

hello if any one have papers vof hpcl or sail, plz send me

0 Answers

what is mean by harmonics

1 Answers

what is the use of CurrentTransformer in AVR ?

2 Answers

a 120 60 watt incandescent lamp has to be operated from 50 c/sec 1 phase ac supply. in order to do this a circuit element has to be connect in series with the lamp. which one of the following sries element is preferable.

1 Answers SSC,

What are the differents between Breaker & Contactor?

8 Answers

iam interesting to design the control panel for 3 phase pump motors by controling single phase switches.iam plan to use fuse,contactor & relay for motor protection .how can i select the voltage & amps rating for fuse,contactor & relay plz guide me .if anybody clarify my doubt means it will more helpful for my future .

1 Answers

Difference between Lugs and Thimbles

0 Answers ABB,

What is the difference between lubricating oil and insulating Oil?

4 Answers Orchid,

For more Electrical Engineering Interview Questions Click Here