Answer / bharat

In electric motor there are three windings.
U, V ,W ,respectively, so measuring of resistance of motor first. switch off electriacal system.
then take e Multimeter and set on Resistance / O'hm. then both cord of multimeter put on U-V winding.. and see the multimeter reading and note..

Answer / jem

plss help me how to calculate an ohmmeter?...

pass this questions to all plssss help me....

hoping for your answers b4 feb.1.......

I KNOW THAT ALL OF YOU HAVE A KIND HEART..........

THANKS A LOT OF YOU.........

Answer / sundar

I know the motor power and motor winding gone then how i
know this motor is good or bad. so i want calculat motor
resistance from motor power.

Answer / bhuvan sharma

firstly separate the both connection means main and aux winding then find out the both windings resistance by multimeter .

Answer / sarath nair

Disconnect motor terminals and check the winding resistance
with a multimeter at the two ends of each coil(U-U1,V-V1,W-
W1) and find the minimum acceptable value by using the
formula (Rated voltage (V)/1000+1)

Answer / d ramesh

disconnect the motor terminals, connect the multimeter
between r-phase two terminals,then multi meter reads the
resistance of the motor winding in r-pahse, similarly for
y&b-phases.

Answer / r.p.samy, national switchgears

Pl check how the winding of motor is connected . Whether it
is Star or delta we have to use 4 probe Ohmmeter ,
preferably injecting a current of 10A . The resistance can
be accurately measured

Answer / daher

bring motor, open cover,disconnect motor winding,make each
phase separetly,use muttimeter,select ohm reading
(resistance in ohm),put the tester probs on 1 phase
terminal,look at tester pointer how much the
reading ,reccort it .

Answer / shashikant

there is One meter Called Motor winding resistance meter
(Ohmmeter). it does have four termainal namely 2 V(+ and -)
and 2 I(+and-), all the four terminal are connected to the
winding of motor to which we want to calculate the
resistance,namely Voltage leads are near the studs of the
winding and current leads are connetcted at the edge of the
studs so that while applying the voltage the resistance of
the winding can be calculated rather the the resistance of
the outer studs.This methos is allowed for both D and y
connection.........
Namaskar

Answer / daher

use DC voltage source to check the resistanceof motor
winding plus multimeter

What is the average hieght of a electrical tower? what are the factors that are taken into consideration for deciding its hieght other than voltage level?

1 Answers  

hi,every one, i have to write the search paper on "performance policy optimization" of NGN (next generation networks). i need the material on this topic. can any body help me. please tell me any useful site where the good material is available and name of any reference book. it should be a great help for me.

0 Answers  

How one can check the charger of the mobile phone or any other charger .......... that is it working ? if , working is it delivering the required supply which is needed by the battery to charge properly ?

4 Answers  

2. The heaviest and lightest strings on a certain violin have linear densities of 3.0 and 0.29 g/m. What is the ratio of the diameter of the heaviest string to that of the lightest string, assuming that the strings are of the same material?

1 Answers  

Why does the radius of armature is less than the radius of pole shoe?

0 Answers   ABB,

Dg pf .71 i am improve pf 0.80 what capacitor connected in dg how?

0 Answers   AVT Natural Products, EMC,

In CDG type IDMTL realy O/L , E/F, O/C which are used for out going feedrs,on R-phase o/c element, Y-phase , e/f elecment and on b -phase o/c element will be connected . Why the earth fault on center phase only, why not on other two phases?

2 Answers  

Explain difference between stand by earth fault and residual earth fault protection?

0 Answers  

want to know about DMRC

4 Answers  

i have 2kv ups how many watts batteries is required

2 Answers  

What are the difference between normal application Transformer and Solar application Transformer?

0 Answers  

What is the difference b/w earthing & grounding?

6 Answers