Answer / vinayak

ans is kva/1.732*volts

so 500kva/1.732*433 volts = 666.66amps on lv side

and 500kva/1.732*11000v= 26.24 amps on hv side

Answer / mohd mansoor

For 500 kva, It's depend on Voltage,some countryes have
different voltages, according to india,


if ur apply the formula- KVA=1.732x Volt x Amp x 0.8

1kva= 1.39 Amps,

500 kva x 1.39 = 695 Amps.

Answer / ashish

For 500 KVA Transformer the full load current is 696 Amp.
So we Can Supply the load Upto 696 Amp only....

Answer / kapil

what is .8 doing in the above formula, while the rating is
given in the KVA and not in Kwatt.

the formula is ..KVA=1.732x Volt x Amp
where voltage will be taken as 415 volt. which is very
common in 3 phase motor rating.
this will produce the same answer as above [695 amps]

Answer / jyotirmaya patra

From where you got all these voltage like 440,415,433.

The simple formulae for calculation of current I, if KVA is
given ;

I = (1000 X VA ) / 1.732 x V

So put your available system voltage and get your answer.

Answer / nwachukwu kelechi

The general formula for a 3-phase power transformer is
given by:
power(KVA)=1.732*V*I*pf.
therefore,depending on the pf under consideration, assuming
a unit power factor,500kva power and input voltage of
11000V we have;
current(I1)= 500KVA/(1.732*11000*1)=26.24Amps.
If the output voltage is 400V, the current will then be:
current(I2)= 500KVA/(1.732*400*1)= 721.7Amps.

Answer / senthil kumar.g

1 kva=1.33amps for EB
1kva=1.39amps for DG the varation is bcoz of p.f

Answer / attique ur rehman

the formula for calculating Single Phase Current is

I = 1000 * KVA/Voltage

Formula for calculating Three Phase Current is

I=1000 * KVA/voltage * 1.732

So for 500KVA we can calculate as below

I= 1000 * 500KVA/440 * 1.732 = 656.6Amps (Depending on
Voltage), if the voltage rating is changed your amps will
automatically change

Answer / kuttivenu

To calculate the Current

Kva= 1.732*V*I/1000
Ams=696A

Answer / mohamed ali.m

Formula is here

Example : 500KVA ( 500x 1000) =500000VA
: 500000/415/1.732= 695 Amps

what do you mean by linear and bilateral network?

2 Answers  

what is the long transmission lines

2 Answers  

why don't we use the generator as a motor? and what will happen?

0 Answers  

How much the fault level of 11 k.v.,22 k.v., 33 k.v. (in Maharashtra- M.S.E.D.C.L) for calculation of short circuit current & selection of h.t.cable.

1 Answers  

how to convert psi into kilo pascal? what is the suction pressure & discharge pressure of chiller?

1 Answers  

1)what is hypo test. 2) which cable need to hypo test.3) when hypo test can be done before or after glanding.4) what is the purpose of hypo test.

5 Answers  

How is the connection of the tap changer on the HV side been made?

0 Answers  

Explen all type electrical protection ? like O/C,E/F,NPS,VOLTAGE UN BLANCE,CURRENT UN BALANCE,NAGETIVE PHASE SEQ,AND ETC...............electrical Protection

6 Answers   Reliance,

we have one ups its neutral is not earthed.its one distribution MCB has a earth fault.but we can not put off any MCB.so how to find out that in which circuit is earthed without isolating the breaker.

3 Answers   CFCL,

can anyone plz tell me in 3 phase induction motor, whare we use STAR CONNECTED MOTOR and whare we use DELTA CONNECTED MOTOR

3 Answers  

what is the use of reactive power

3 Answers  

Distinguish between nuclear power station with thermal power station for initial cost, starting period, cleanliness, and transportation of fuel

0 Answers   IOCL,