WHAT IS BASICS TO SELECTION OF 11 kv Trasformer, send any
calculation sheet for selection of transformer

Answers were Sorted based on User's Feedback



WHAT IS BASICS TO SELECTION OF 11 kv Trasformer, send any calculation sheet for selection of trans..

Answer / shiva

for any application selection depends on local distribution
(sub station ) transmission ,secondary voltage and finally
depends only on demand KVA of u r plant.

Is This Answer Correct ?    5 Yes 0 No

WHAT IS BASICS TO SELECTION OF 11 kv Trasformer, send any calculation sheet for selection of trans..

Answer / anuya

Basic & most important factor is transformer capacity which
can be derived by calculating all connected loads at
downstream. It will give the KVA rating.
Primary-secondary voltage ratio & vector group.
Environmental conditions like temp, etc. Application
Indoor/outdoor.
Cooling type requirement will deside the Xmer will be Oil
cooled or dry type unit.
Impedance of the Xmer.
Load type.

Is This Answer Correct ?    6 Yes 5 No

WHAT IS BASICS TO SELECTION OF 11 kv Trasformer, send any calculation sheet for selection of trans..

Answer / prabhu gnanasekaran

11 KV transformer or anyother transformer the calculation
of the transformer is done only as per the loads connected
in it(Continious load,stand by load and Auxillary load). No
of motors connected to it,KW rating of the mator, Total
line current of all motors.
If it is 11 KV the your primary side of the transformer is
11 KV thats all. Due to this 11 KV the line current
calcultation will change in the factor of system voltage
level in Line current calculation of the motor.

Is This Answer Correct ?    8 Yes 16 No

Post New Answer

More Electrical Engineering Interview Questions

The magnitude of sum of two sinusoidal av voltage is equal to 230 volt.the magnitude of each individual voltage is also equal to 230 volt.what must be the phase difference between voltages?

0 Answers   PGVCL Paschim Gujarat Vij Company Limited,


What is diference between ELCB & ELMCB?Also how its application for use in design area?

2 Answers  


What is expand formation of AYFY cable

2 Answers   HP,


If a HV Underground Cable (13.8KV) is layed in the ground below 1.5 Mtrs and any building construction is done on the Cable route. IS this allowable or Not? What should be the clearance. As per ISO construction on HV cable route is safe or Not? Why? Can any body suggest the site for my question?

1 Answers   ZCL,


why are the likely reasons for bochholz & pressure relays oprate due to a internal fault but not differential relay ?

2 Answers  






which metal is use in shunt

4 Answers  


Why DG self motor winding burnt out?

1 Answers   Aegis,


Can we test the alignment of End shield and stator of turbogenerator without rotor insertion? Also how to fix maintain the alignment at site installation?

0 Answers   Deccan Cements,


(1)Can earth and be conected together (2) what is the diferent between earth & neutral

0 Answers   VACC,


what is "PE" earthing? and what do u know abt 16mm cable?

1 Answers  


i want to ask that as everybody knows that in star connection on star point is called neutral. my question is that why on that poin called neutral. what is the reason behind it. what is the logic behind it. i heared somewhere that on this point all phases current become zero thats why. if this answer is right then prove why on that point is current become zero. if this answer is not right then tell me the right answer. post ur answer here or on my mail address. m.ikram786@yahoo.com m.ikram555@gmail.com. thanks.

1 Answers  


Where I can get the sample question for post of Junior engineer electrical-II For RRB Bhubaneswar.

0 Answers   Noida Power,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)