Answer / bhanu mahesh

A ton of cooling capacity is the amount of cooling that
would be provided by melting a ton of ice. Thus, a central
air conditioning system that is rated as a 2-ton system
would provide the same cooling as melting two tons of ice
per day (24-hour period).

Ton vs BTU
A ton is equal to 12,000 BTUs. Thus, a 2-ton air
conditioner is equivalent to a 24,000 BTU air conditioner

Answer / rajan s.k.

It is equivalent to the production of cold at the rate at
which heat is to removed from one US tonne of water at 32 0
F to freeze it to ice at 32 0 F in one day or 24 hours, and
is denoted as TR

Thus


1 TR = (1*2000 lb * 144 But/lb) / 24 hours
= 12,000 Btu/Hr
= 200 Btu/min

Answer / mahesh

1TR-
"The amount heat required to extract from 1000kg of water
to convert it into ice,in 24 hrs from 0 degree water to 0
degree ice.

1TR = (1000Kg * 335kj/kg)/(24*60*60)
= 3.8kw
= 3.5kw

Answer / vikas

It means that a particular device is able to convert 1
tonne of water i.e., 1 lts. into ice in 24 hrs. (at ideal
conditions).

Answer / bhavin cauhan

A Machine Which can make 1 ton of ice in 24 hour from
water....i.e It is the rate of heat removed from the water
to make it ice

Answer / ansar

1ton ac is take 1.2kw electrical load

Answer / s.dency

The tonnage is shortly called as Ton which is the unit of
measurement. It measures the amount of cooling capacity of a
system. One ton of cooling is based on the amount of heat
needed to melt one ton (2000 lbs.) of ice in a 24 hour
period. One ton of cooling is equal to 12,000 Btu/hr.

S.Dency
http://dencyinspired.blogspot.com/

Answer / harshal v.p.o

1 tonne AC : it is the capacity of the compressor of Air
Conditioner,which can remove the heat generated in the
particular room,such that the amount of heat is equivalent
to melt a block of 1 tonne ice in 24 hours.

Latent heat of ice= 144 BTU
1 TR= 144 X 2000
= 288000 BTU/24

For 1 hour

If you dividing by 24
288000/24=12000BTU


Thank You
Harshal VPO
Tanur

Answer / c.m.kashif abrar

The amount of hear absorbed by melting one ton of ice in 24 hours. Equal to 288000 Btu's per day 12000 Btu's per hour or 200 Btu's per minute.

Answer / harshal v.p.o

1 tonne AC : it is the capacity of the compressor unit,
which can remove the heat generated in the particular
room ,such that the amount of heat is equivalent to melt a
block of 1 tonne ice in 24 hours.

What type of a DC motor would you use for a lift?

0 Answers   GE,

why PT transformer primary r the grounded?

2 Answers   L&T,

What is C-factor?why it is required to consider in fault short circuit calculations?

2 Answers  

what is the function of potential transformer in s/s

6 Answers  

what is vtg limit of earth and neutral at transformer side?

0 Answers   IOCL,

i have 28/32 MVA power transformer with 11/6.6 KC voltage rating and 12%impedance.it have star connection at both side.but it have another thied winding tertiary winding.what is used of this winding. pl tell me

7 Answers  

why test lamp didn't glow across 500v megger?

4 Answers   Aurobindo,

Why different Pressure switch used in marine boiler water circulation system

0 Answers   MMD,

Any one can explain if there is any harm from humming noise heard from air circuit breaker : we have 415 switch board having two incomers from transformers 3.3KV/415V , when bus coupler closed, and open one ACB incomer to work in one of the transformers, the current started hunting around 50 Amps, and heard humming noise from the air circuit breaker, although the load current was only 1200 amps while the ACB capacity is 2500 Amps, and the transformer 1600 KVA. The same didn't happen when taken the other transformer offline. Why this humming noise and current fluctuation? is there any implication or danger, bearing in mind that we just returned everything back to normal and stopped the maintenance of the transformer. Shall we go ahead and ignore this noise?

6 Answers  

what happen if we give 220 volts dc supply to d bulb r tube light?

4 Answers   Genus, RMSI,

What is mean by powerfactor. What is the difference between leading and lagging power factor?

2 Answers   HCL,

I have raw material for making Compact-Choke for flourscent lamp of 40 Watts. We are suppose to get 0.4 amps output at end. but we are getting 0.42 or 0.44 amps and above. We have done many testings in different but nothing worked out. Please suggest me how to get the correct output. We are using 1. core winding of 700 windings of aluminium 2. E-shape iron fillings and I-shape iron fillings to surround the winding.

6 Answers