Answer / ashraf majid

Three Windings are required Where U require three levels of
voltage.These windings are
1.HV (High Voltage) Winding
2.IV (Intermediate voltage) Winding
3.LV (Low Voltage) Winding
The main task of voltage transformation is performed by HV
winding & IV winding, while as LV winding is used for minor
purposes as auxilliary winding

Two winding transformers are more common and used for
transformation of One voltage level into another.

Answer / m. k

Three winding transformers can also be used in the places
where you have space constraints, there ispite of giving
two no. two winnding transformers one no. three winding
transformer can be used.

A three winding transformer can be can have following
configurations:
A.Configuration-1
1.HV (High Voltage) Winding say 400 kV
2.IV (Intermediate voltage) Winding say 220 kV
3.LV (Low Voltage) Winding say 6.3 kV

B.Configuration-2
1.HV (High Voltage) Winding say 400 kV
2.LV-1 (Low Voltage) Winding say 13.8 kV
3.LV-1 (Low Voltage) Winding say 13.8 kV

With this configuration if we say that MVA capacity of
transformer is 220 MVA (say) at 400 kV, them at 13.8 kV (LV-
1 & LV-2) windings will have MVA capacity of 110 MVA each.

Answer / agus

There is also another application of three windings
transformer with unloaded IV (Intermediate voltage) delta
winding. The function of this kind of IV delta winding is
for reducing unbalance in the supply side, when this
transformer is delivering power to an unbalance load.

Answer / haroon

one more name of teh third winding is known as stabilizing
winding

Answer / abhi

three winding transformer is also used to suply LV. voltage
for two same capacity load at secondary side ....

Answer / yashar

Tree Winding transformers are used to supply DC Bus bars
also, and in this case rectification will be better becuase
12 pole will be used.

Answer / p.sandeep

If we use on load tap changer we make 3 winding transformer.is it ok

Answer / vikas v

A three phase tfr is three winding tfr and single phase tfr
is two winding tfr

When can we take Neutral as common neutral link?

0 Answers  

some ac motor's direction get change dueto ghanging input to the ac drives.(say ryb to rby). but some motor direction remains the same when phase sequence is changed fromdive side. can anybody guide me?

1 Answers  

What happens when generator is running with leading power factor on it say -0.96. what are the effects of it on alternator and the other generators operating in parallel to it.

2 Answers  

we have a 2000kva step down transformer at our site. The HT side is charged from 22000V. So the primary current will be 52.48A. So why the HT breaker(SF6 ABB) is rated of 1250Amps ?

2 Answers  

Application of statically induced emf

0 Answers  

what are the effects on an power plant and consumers if the power factor is increased or decreased?

2 Answers  

WHY WE USE CABLE JUNCTION AFTER BETWEEN TANSMISSION LINE AND TRANSFORMER

1 Answers   L&T,

How does MCB operate without relay..?

10 Answers   Toyota,

Wtat is vaccum currcuit breaker.define with cause of used.and where be use it Devise .

1 Answers  

In synchronous generators field is rotor and armature is stator.Can we take the output at the rotor in case of synchronous generator by the dc excitation on the stator?

2 Answers  

Where -48 volt DC use & why?????????

10 Answers   Ericsson, INDUS, Indus Towers, Telecom,

Since phi is the angular displacement between V & I, then why we use phi in power triangle ie. when showing active, reactive & apperent power in triangular manner & if it is ok then where is V & I in the triangle.

1 Answers