Answer / d.sanadi

OTCC??? it should be either OCTC(OFF CIRCUIT TAP CHANGER)
OR OLTC (ON LOAD TAP CHANGER). Tap changers are basically
used to adjust the secondary voltage to a range of +/-5%

Answer / b.krishnaswamy

OCTC- Off circuit tap changer is meant for changing the
secondary voltage of power transformer within the rated
plus minus range with respect to the rated nominal
secondary voltage by shifting the tap positions.. As the
name implies the taps are changed only when the transformer
is taken off the circuit.

Answer / sudhakar ghait

OLTC - ON Load Tap Changer. When primary voltage low/high
in that condiction we will maintain our secondary voltage
by using our transformer's OLTC

Answer / b.krishnaswamy

It should be OCTC-off-circuit tap changer or OLTC- On-load tap changer. OCTC is for changing the taps provided in HV side of the transformer when the transformer is out of cicuit , as the name implies, for changing the voltage ratio. In OLTC the taps can be changed when the transfomer is on load. The number of taps provided depends on the design requirements for change of secondary voltage on the + side and minus side relative to the rated voltage ratio.

Answer / jalees divker

Question May be regarding RTCC
if it that mean remote Tap changing cubicle, this cubicle normally installed in control room/or any suitable place, to change the Tab of transformer ,whenever desired as per Grid voltage, It could be Manual/Auto operated.

Answer / parthi

secondry voltage adjustment in rating

Answer / venkatesan.j

It is a part of the HV winding ,as the current is low. It
is used to step up or down the voltage according to the
requirement.

where HT & LT capacitor uses ?

2 Answers   NTPC,

how synchronous condenser is used in place of synchronous generator with out negotiating IEEE standards? Can i use 3 generators as synchronous generators and 2 generators as a synchronous condensers in an IEEE 14 bus system with out disturbing the standards?

0 Answers  

on 22.03.2015 at 17:15hrs Y phase 66kV class Power Trf-2 Current transformer has flashed over and oil came out. The failed CT has been replaced on 24.03.2015 at 13:15hrs and the Trf has been charged in presence of RT Hassan after conducting the pre-commissioning tests. On the same day at 17:00hrs the commissioned CT has again flashed over and immediately the Trf  has been isolated from power supply. It is confirmed the secondary is not opened and checked the earth integrity and is found ok. Here what would be the reason for the CT failure? 

2 Answers  

what is the ideal earth resistance

11 Answers   Amit Enterprises, Enercon,

What is Grounding?

2 Answers  

Can Induction motor run at over rated speed? ( 15oo rpm is rated speed for 50HZ. is it possible to ride 3000 RPM with same motor with the help of VVVFD for continues ride of 100HZ)

3 Answers   Equate,

why generator is design for lagging P.F(power factor)?

3 Answers   BSES,

how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec.

0 Answers  

How the electric train gets the supply of electricity? What is the return path of the current?

7 Answers   NTPC,

how to calculate bus-bar sizes? (copper bus-bars)

2 Answers  

What is the difference between single core 2 wire and single core 3 wire system? Which application we are using this? and for What purpose we are using this?

0 Answers  

Whats the frequency used in Rodents Repllant System????? What is the Diff btw Infrasonic & Ultrasonic Frquencies???

1 Answers   Emerson,