What is the most common cause of solid size segregation in bulk solid systems?

0 Answers   TATA,

---

What is a "saltation velocity"?

0 Answers  

---

i badly need a chemical process details for making a project...plz help me out......i m a btech final yr chemical engg student in a govt univ,and we have to make a detailed project on any chemical process with contents like...intro,kinetics , material balance,thermodynamics,process layout,process design,physical conditions,plant location,cost estimation etc.............if any one could help me i will never forget hi thankless work and always try to help u in whatever u ask.............

2 Answers  

---

we have 2 O2/Comb Analyzers Servomex Model 2700 in service for one of the furnaces in our chemical plant. It is giving High Temperature Alarm. Checked Temperature and found it to be 800 Deg C whereas Set Point is 700 Deg c. It is strange why is temperature not at SP. Also response is 23 % with 21 % Inst Air and with N2 reading is not coming down. please clarrify this issuses very urgent

1 Answers  

---

respected sir,i have been selected in the written examination(CHEMICAL) of IOCL Panipat held on 30 m1rch, So please tell me which type of questions asked in this interview frequently.Can u mail me some questions?

22 Answers   HCL, HCPL, HPCL, IOCL,

---

Explain what are the assumptions made on conservation equation?

0 Answers  

---

Question 64 – According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

1 Answers  

---

how to improve recovery of product in packed tower(raising ring) recovery of vinyl acetate from VA+WO ( vinyl acetate +waste oil mixture)

0 Answers  

---

PROCESS DESIGN - EXAMPLE 21.3 : According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

1 Answers  

---

What are the specialized crushing methods?

0 Answers  

---

Question 36 - For a mixture of benzene (B), toluene (T) and xylene (X), the equation applies where x for B, T and X will sum up to 1. The equation of x for each component is x = (L / V + 1) (F) / (L / V + K). The data of F for each component are : 0.5 for B, 0.35 for T, 0.15 for X. The data of K for each component are : 1.98 for B, 0.76 for T, 0.24 for X. When x for B + x for T + x for X = 1, find the values of (a) L / V; (b) x for each component of B, T, X respectively. You may use Excel program - Data : What-If-Analysis for Goal Seek to perform the iterative calculations.

1 Answers  

---

Explain how can you determine the proper pipe thickness for a slurry line?

0 Answers  

---