State 5 different method of level measurements.

Answers were Sorted based on User's Feedback



State 5 different method of level measurements...

Answer / hitesh

five TYPE OF LEVEL MEASUREMENT
1> DIP TUBE METHOD
2> DIFFERENTIAL PRESSURE METHOD
3> ULTRASONIC METHOD
4> NUCLEONIC METHOD
6> RADAR TYPE

Is This Answer Correct ?    6 Yes 0 No

State 5 different method of level measurements...

Answer / abhijith

five type of level measurements,

1. Capillary type
2. radar type
3. ultrasonic
4. differential pressure method
5. capacitive type

Is This Answer Correct ?    3 Yes 0 No

State 5 different method of level measurements...

Answer / usman

1 guage glass
2 dip stick
3 pressure transmitter (open tank)
4 diff pressure transmitter (close tank)
5 radar type
6 displacer type
7 ultra sonic waves
8 capacitance probes

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

Can anybody tell me which type of question are asked in the interview for the FORMULATION(Pharma) as a instrumentation engineer, & question in building managment system.

0 Answers   Reddy Labs, ScienceWay,


i have height of stem drum level 1000mm.how i calculate the DP transmitter

2 Answers  


Can any one tell me what type of question asked for instrumentation and control interview panel??? pls mail ramashankar.goel@gmail.com

0 Answers  


what can of fault ofently come in vibration mesurement?

0 Answers  


hi... i'm about to learn siemens plc i came across following question in my mind ... plr ans 1. hw motor operated by plc 2. hw drive operated by plc explain dis by both ladder logic diagram and hardware config , connection

2 Answers   KCP Cements,






How to measure high frequency using thermistor

1 Answers   DRDO,


capillary type tranmitter using remote seals and capillary tubes filled with liquid of known of known density so if you wanna callibrate it just close block valve just before capilary @ high side & connect druck apply it's calibrated range pressure as normal calibration ensure low side block valve must be closed & if you asking commissioning so this is not a DP type pressure tx so simple if you wanna put in servie this tx just open high side block valve & than low side block same way i do it but still transmitter showing -13 ma.just tell me what i want to do ?

1 Answers   Gasco,


What is DCS and PLC scanning time?

5 Answers  


how to install Differential pressure transmitter in gas line.i need transmitter down side.

7 Answers   Rockwell,


whats the working principle of level transmeter?

6 Answers  


Why is the orifice tab provided?

0 Answers  


How will you calibrate an Absolute Pr.Transmitter of range 400mmHg absolute ?

0 Answers   CCIE,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)