Follow Our FB Page << CircleMedia.in >> for Daily Laughter. We Post Funny, Viral, Comedy Videos, Memes, Vines...


How much overlapping required for welding the reinforcement
bars in Columns & beams

Answers were Sorted based on User's Feedback



How much overlapping required for welding the reinforcement bars in Columns & beams..

Answer / er.subramaniyan

AS Per is code welding req.20dia of steel
doing welding in three point
1.starting point
2.middle point
3.end point
welding length 5cm

Is This Answer Correct ?    2 Yes 1 No

How much overlapping required for welding the reinforcement bars in Columns & beams..

Answer / desai

50*dia of bar or ld

Is This Answer Correct ?    0 Yes 0 No

How much overlapping required for welding the reinforcement bars in Columns & beams..

Answer / parvesh saini

16D

Is This Answer Correct ?    0 Yes 0 No

How much overlapping required for welding the reinforcement bars in Columns & beams..

Answer / arka

Please check IS 9417 for welding in reinforcement.

Is This Answer Correct ?    0 Yes 0 No

How much overlapping required for welding the reinforcement bars in Columns & beams..

Answer / ronak shah

in which IS Code it is given. i think is 10d. full welding
form both the face of the bars.

Is This Answer Correct ?    0 Yes 1 No

How much overlapping required for welding the reinforcement bars in Columns & beams..

Answer / thiagarajan.m

50* d. ..ie fifty times of dia of main reinforcement

Is This Answer Correct ?    4 Yes 7 No

How much overlapping required for welding the reinforcement bars in Columns & beams..

Answer / sjtbehera

actual as per thumb rule lapping of bar is 50d required.
but it is actual depends on development length. welding is
required where 36 dia and above bar. beyond that is not
necssary.

Is This Answer Correct ?    0 Yes 3 No

Post New Answer



More Civil Engineering Interview Questions

WHAT IS THE IMPORTANCE OF FLY ASH BRICK?

2 Answers  


how many labour is required for 1cum of concrete?

6 Answers  


what is the Purpose of Adding 20% of wet mortar & 1/3rd to Dry Mortar for PCC & Plastering & Rcc .is there any standard method for adding this .?

0 Answers  


Explain the importance of moment of inertia?

0 Answers  


why we can use dust in concrete insted of fly ash

0 Answers  






is there zone 6 for earthquake in india? on what basis the naming of the zones are done in variuos countries?

2 Answers  


if dia of inner circle is 42 m and depth is 1.5 m and width is 1 m ,then whait is the quantity of steel?

0 Answers   AZT Techno,


what is steel

3 Answers  


please give me the rates of RCC(CUM), PCC(CUM), Brick Work(CUM), Tile Flooring, Saria Shuttering

0 Answers  


please what are the required bars for a beams of 6mx6m and 450x300mm, one is continuous and the the second is discontinuous ..Its a commercial building (church)

0 Answers  


What quantity of 1.0 m3 bricks required?

0 Answers  


how is the wastage component in structural steel being considered while doing the reconcillation for the fabrication with returning of scrap under 1 meter length

4 Answers   LIC, NTPC, Tata Steel Limited,






Categories
  • Civil Engineering Interview Questions Civil Engineering (5076)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4445)
  • Electrical Engineering Interview Questions Electrical Engineering (16606)
  • Electronics Communications Interview Questions Electronics Communications (3915)
  • Chemical Engineering Interview Questions Chemical Engineering (1092)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (214)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (258)
  • Instrumentation Interview Questions Instrumentation (2992)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (123)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (0)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1378)