Answer / g.karthikeyan

M20 - 1(Cement):1(1/2)(Fine aggregate):3(Coarse aggregate)
M25 - 1(Cement):1(Fine aggregate):2 (Coarse aggregate)

Answer / shabarish

mM20 : 1:1.5: 3

M25 : is a design mix. & the proportion can be obtained
only on the basis of materials required & only in the lab.

Answer / ashish

M20 1:1.5:3
M25 1:1:2
M30 will depend upon the mix design

Answer / bhavna tripathi

The mix proportions for M20 & M25 both, shall be designed
by laboratory trials and designed according to BIS 10262,
383 & 456 or SP 23. The ratio 1:1.5:3 was given earlier in
IS 456 but IS 456 (2000) does not recommend volumetric
batch for even M20 and hence both should be designed as per
requirement, i.e. it depends on the type of cement,
gradation of aggregates,workability required and
importantly the water cement ratio.

Answer / nimmakayala

M10 manual mix, proportion is 1:3:6(C:FA:CA)
M15 manual mix, proportion is 1:2:4

> M15 are design Mix, and proportion on Weight basis (not by
volume basis) depend upon grade/type of cement, type of fine
aggregate and Coarse aggregate

However for the estimate purpose the cement can be calculated
For M15 (1:2:4)– cement is 6.37 bags/Cum
M20(1:1.5:3) Cement -8.09 bags/Cum
M25 (1:1:2)cement -12.2 bags/Cum

Answer / tiru

M20 1:1 1/2:3
M25 1:1:2
M30 Proportion not specified its depending upon mix design'

Answer / sobhanbabu

M5,M7.5,M10,M15,M20 -nominal mixes(by wt or by volume)
M25-both nominal and design mix
M30,M35,M40-design mixes(mixes designed specially in lab)

Answer / dasari

M20 1:1(1/2):3
M25 1:1(1/2):2
M30 1:1:2

Answer / aditya richie

concrete is designed by Job Mix Formulae, not just by
taking some standard values

Answer / muthazhagi

M 15 - 1:2:4 , M20 - 1:1.5"3 , M30 - 1:1:2

what is SPLICES & where it is used?????????????

3 Answers  

what are the diffrent kind of grades in concrete and what does M means while specifyng the grades?

10 Answers   Gammon,

need to join coaching institute in coimbatore tamilnadu ......say me the best coaching for IAS

0 Answers  

what is fe 415 steel

15 Answers   L&T, Nabard, Rahul Computers,

Design a shear wall of length 4.20 m and thickness of 250mm subjected to the following forces.Assume Fck = 25Mpa and Fy = 415Mpa and the wall is a high wall with central part 3440mm x 250mm and two 380mm x 760mm strong bands at each end with following loading. S.No.       Loading        Axial force      Moment     Shear 1               DL+LL          1950              600            20 2           Seismic load       250              4800          700

0 Answers   L&T,

Define What is the force exerted by the Tacoma narrows bridge?

0 Answers  

what is the meaning of sleeves in reinforced concrete????. where its coming???.

1 Answers  

what is the difference between gypsum and pop?

7 Answers   ncrt,

Howmuch bend to be provide for 200/600 BEEM

0 Answers  

Pl. enlighten whether M20 grade RMC is suitable for columns & beams for 5 storied residential building

6 Answers   L&T,

what is the initial setting time & maximum duration concrete get hardening for ordinary portland cement?

5 Answers  

wat is six sigma course ? is it good for civil engineers . wat is pmp certification ? is it good for civil engineers .

1 Answers   CCCL,