HOW WE CALCULATE CURRENT IF THERE ARE NOT PRESENT ANY AMMETER
OR MULTIMMETER??????



HOW WE CALCULATE CURRENT IF THERE ARE NOT PRESENT ANY AMMETER OR MULTIMMETER??????..

Answer / Shreekant Gupta

If an ammeter or multimeter is not available, you can calculate the current indirectly using Ohm's law. First, measure the voltage (V) and resistance (R). Then, use the formula I = V/R to find the current (I).

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

how will you determine the short circuit capacity of a network

3 Answers   Dalkia,


whenever a squirrel or a crow gets tangled near the out put of the feild transformer there is a discharge of 440 volts of current through the neutral due to which my appliances blow up causing a huge bang.will the RCCB help in these conditions

1 Answers  


what is the difference between AC choke (inductor) and DC choke (inductor), working and design point of view?

2 Answers   Electrotherm,


What are the two major types of control system?

1 Answers  


Is pure capacitor load and pure inductor load is an linear load? pls justify

2 Answers  


7- What is the Dissipation Factor and the difference between it and Insulation Resistance Test? 8- What is the task (function) of DC and AC reactors in power plant? 9- What is the task (function) of (open delta with earthed) in some types in transformers? 10- What is the base of the selection of the vector group in transformers? 11- What is the zig-zag transformer and its function by drawing in large detail? 12- What is the polarity ? 13- Why we make short between phase(R) in high side and phase (r) in low side in vector group test? Where High Side ( R ,S and T ) and Low Side ( r ,s and t ). 14- What are the time on delay and time off delay? 15- What is the vector group? 15- What is the task (function) of different types of vector group such as Dyn11 , Dd0 , YNd1,……..,?

1 Answers  


What will happen if 230V DC motor connected to 230V AC Supply?

15 Answers   Ashok Leyland, BOC, JSW, ONGC, RRB, TRB,


what is STUB protection in tranmission system and switch yard area?

9 Answers   KSEB, Power Grid,


what is the spdt

1 Answers  


Can a 150 kva 3 phase,440v/230v delta-wye connection stepdown transformer can be used in reverse as a step up tranformer ?

3 Answers   Meralco,


why the generator operating along with the infinte bus bar should never be under_excited?

1 Answers  


A 3-phase IM is supplied from 50 Hz system. It runs at speed of 1440 rpm and slip equal to 4 %. Calculate rotor frequency. A 50 Hz B 0 Hz C 4 Hz D 6 Hz

3 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)