Answer / sandeep m. parmar

yes a step down transformer can be used as step up if the
connections are reversed.

Answer / j.karthik

ya,its possible.. for ex: using a 11kv/415volt step down
transformer, in this primary voltage is 11kV and the
secondary voltage is 415volt(step down transformer)... now
we giving the input voltage to the 415volt side of the
transformer now the primary voltage is 415volt and secondary
voltage is 11kV(step up transformer).....
The step up and step down transformer is deponds upon
the input voltage is feeding side of the transformer(Primary
or secondary side)

Answer / lokeshraj

Yes we can use this in both step up and step down. But the
transformation ratio is not same in both case. It would be
slightly different.

Answer / sandeep m. parmar

yes i gave a short answer which is elaborated by Mr.J
Kartik. he is right.

Answer / akatugba

On the issue of reversing step down as step up....Do you
ever put the 4poles into consideration..What now happen to
the grounding for protection, is the 4th pole for grounding
going to be on the 11kV outgoing? or on the incoming
415volts

Answer / manoj

no, b'coz step up & step down t/f is design perposly,it
depend on wdg,for step down no of pri wdg more sec wdg
less,& for step up no of pri wdg is less & no of sec wdg is
more.

WHAT IS THE ROLE OF ELECTRICAL & ELECTRONICS ENGINEER IN TCS.

2 Answers   CTS, TCS,

Dear Sir, we met a disaster with our 62.5 kva genset, after rewinding we informed by our contract engg that due to return current coming in neutral & impropper earthing this happend. But after all set up & load balance we checked & found again we have about 20 to 32 amp return current on neutral. we have 12 airconditioner + 12 mini fridge on single phase line. Pl suggest any idea to solved this problem

3 Answers  

A synchronous motor is operating at a leading power factor .if the applied voltage is decreases ,(the excitation remains constant ) ,the motor current a)increases b) decreases c)remains same d) none of these

2 Answers  

Why different values of B’s (magnetic flux density) are chosen for DC machines and Induction Motors?

1 Answers  

In Plumbing services What are accessories we consider for a bathroom?

0 Answers  

We have .ht motor which is 60Hz.we run on 50Hz.so that it's speed reduce but we had one prob.that motor winding temp increase up to 135 deg.we want reduce this temp.what to do?we arrange ext.cooling fan but not much effect.we want reduce this temp. Inhouse without affecting much.cost. also don't want reWINDING OF MOTOR?

3 Answers  

how to calculate Amp, 2 different Amp of batteries? Example: No. of Batteries = 2 Battery voltage = 12V 1st Battery rating = 17AH 2nd battery rating = 30AH between parallel connection then output volt 12v Amp?

2 Answers   Bhel, LG Soft,

can any one list the class-a, class-b & class-c trips of power generator?

3 Answers  

One 200 V, 100 W bulb is connected in series with primary of a 200 V, 10 kVA transformer. If its secondary is kept open circuited, then the bulb would have (1) Full brightness (2) Poor brightness (3) A little less than full brightness (4) More than full brightness...explain

2 Answers  

400kw, 3.3Kv motor want to fix 1000km away from substation. What is full load current? and what is the cable size for motor? I amp expecting answer and advice from your side.. thanks...

4 Answers   Kuwait Oil Company, Weatherford,

how the 12 pulse rectifier is made?

8 Answers   Engineers India Limited,

why indicated sypply only by 440V in 3-phase system.

2 Answers